OpenBCM V1.13 (Linux)

Packet Radio Mailbox

DB0FHN

[JN59NK Nuernberg]

 Login: GUEST





  
DL1FDF > QRP      20.04.98 23:01l 89 Lines 4230 Bytes #-10438 (0) @ WW
BID : 204806DB0VFK
Read: DG6MS GUEST
Subj: SIERRA PWR MODS 3
Path: DB0ZKA<DB0ABH<DB0SRS<DB0AIS<DB0GV<DB0EAM<DL0EAM<DB0VFK
Sent: 980420/2037z @:DB0VFK.#HES.DEU.EU [JO41SG TheBox DG5FAU] $:204806DB0VFK
de DL1FDF @ DB0VFK.#HES.DEU.EU   (Steve)

to QRP @ WW

Date: Fri, 20 Mar 1998 13:15:27 -0700 (MST)
From: marion@montana.com
To: qrp-l@Lehigh.EDU
Subject: [6478] Sierra Pwr mod
Message-ID: <199803202015.NAA06783@paw.montana.com>
Mime-Version: 1.0
Content-Type: text/plain; charset="us-ascii"


                Got so many requests on this, Putting it on the list.
Change the rf choke feeding the collector of the final(L10) to a 4 to 1
impeadance ratio transformer. I used the same core material,-43, as the
original choke, but used a 0.5 instead of a .37 inch diameter core.Wind
with 12 bifiliar turns of #24 wire. Form a center tap by connecting the
start of one winding to the end of the other winding. Connect the tap to
the finals collector. Connect one of the other ends to the 12volt line
and the last lead to the input of the low pass filter. I installed in same
location as old choke. One lead to C46 on top side left lead as viewed
from frontof rig. Center tap to hole for collector trace. 
Other lead to hole near C45.

IMPORTANT: installing in original position as I did requires cutting the
trace at C46 to collector, isolating C46 only.
You can use a MRF237 and sink it in original position. I used a RCA
SK9618, which has the emitter as the center leg and mouting tab. Since
the final has emiter to ground, no insulator is needed to heat sink 
directly to back of cabinet with a little heat sink paste. 
There is a convenient ground at PCB to solder emitter to, so only two 
leads are needed to go to base and collector. 
The MRF237 will run hot, but you can beacon with the SK9618
and maybe gets warm. I used a 500ohm pot to the rear panel, to replace
the drive control as described in the Sierra manual. I notched a hole big
enough for the two wires to it to run under the board. 
I ran the two transistor leads on top. 
You will need this control to back off of 6 to 7 watts on
160,80 and 40 meters, or to run at low current levels. With control peaking
transformer wound on the same core.  You can also experimentally stretch
or squeeze toroid windings in the low-pass filters--just check your work
with a spectrum analyzer, because you may compromise the return loss or
spectral purity of the signal by doing this.  
(On the other hand, you may make it better.  
Toroids seem to have as much as a 10% swing in permeability,
and that's *before* everyone winds them their own way :)

As I've pointed out before, the Sierra is designed to meet cost, size,
and ease-of-construction goals, and therefore does not have a complicated
transmit strip.  I designed for the 2-3 watt level at 20 meters.  Power
output is usually higher than this on the lower bands, lower on the
higher bands.  
Of course the S/N ratio is typically higher on the high bands
(because they're usually quieter), so you might consider the lower power
and reduced current drain as a feature for portable operation   :)

But if you really want a 5-watts-on-all-bands Sierra with no tweaking,
you'll have to re-design the transmit strip.  I have built such a strip
on a protoboard; it takes about 30 to 40% more parts than the existing
transmitter design.  (It won't fit in the same space without doing
something I have sworn NEVER to do to the kit builders of the world,
some of whom have marginal vision, and that's use surface-mount parts.)

Basically, what it requires is more gain stages, each with feedback,
resulting in a more "level" frequency response from 2-30Mhz.  It's also
helpful to include ALC or some way of automatically controlling power
output in response to load or drive changes.  You also have to be very
careful not to cause problems with excess in-the-box radiation near
sensitive circuits.  Again, this would be dificult at the Sierra'a size
and price point; you'd probably have to add either a small additional PCB or
some shielding.

Have fun,

waYne,
N6KR

n6kr@elecraft.com
  -- or --
svecbrdk@well.com
-- 
qsp de dl1fdf
=========================================================================
AX25: dl1fdf@db0vfk.#hes.deu.eu   | dl-qrp-ag GM | g-qrp 8769| qrp-l 252
e-mail: bauer@student.uni-kassel.de | 72 de steve DL1FDF -- DL/VY1QRP    
=========================================================================




Read previous mail | Read next mail


 18.11.2026 00:54:06lGo back Go up