| |
G0MFW > TNC 24.07.06 13:13l 80 Lines 3470 Bytes #999 (0) @ WW
BID : F80031G0MFW
Read: OE3GMW GUEST DK3HG
Subj: Re: NEED HELP PLEASE.
Path: DB0FHN<DB0MRW<OK0PPL<DB0RES<ON0AR<I0TVL<GB7YKS<GB7NND
Sent: 060723/0917Z @:GB7NND.#23.GBR.EU #:6690 [Worksop, Notts] $:F80031G0MFW
From: G0MFW@GB7NND.#23.GBR.EU
To : TNC@WW
A JIFFY is an actual unit of time - it's one hundreth of a second.
Willie ZR6WPD wrote:
>I NEED NOW TO INTERFACE {CONNECT} THIS TNC TO MY COMPUTER,SO I WHOULD LIKE
>TO KNOW WHICH PINS I MUST USE FROM THE TNC AS WELL AS THE
>COMPUTER = 9 PIN OF COMPUTER AND THEN THE 25 PIN?????
Hi Willie. You need an RS232 cable between your TNC and computer. Below
are some diagrams of the connections for various configurations.
Serial cables:
DB9F to DB9F DB25F to DB25F
2 --------------- 3 2 --------------- 3
3 --------------- 2 3 --------------- 2
4 --------------- 6 4 --------------- 5
5 --------------- 5 5 --------------- 4
6 --------------- 4 6 --------------- 20
7 --------------- 8 7 --------------- 7
8 --------------- 7 20 --------------- 6
DB9F to DB25F
DB9F to DB25F DB9F -- DB25F to DB9F -- DB25F
2 ----------------- 2 2 --- 3 ------------------- 3 --- 2
3 ----------------- 3 3 --- 2 ------------------- 2 --- 3
4 ----------------- 6 4 ---20 ------------------- 6 --- 6
5 ----------------- 7 5 --- 7 ------------------- 5 --- 7
6 ----------------- 20 6 --- 6 ------------------- 4 --- 20
7 ----------------- 5 7 --- 4 ------------------- 8 --- 5
8 ----------------- 4 8 --- 5 ------------------- 7 --- 4
RS232
Serial Port 9 pin to 25 pin Cable Adapter.
DE9S DB25P
Pin # Control Signal Pin #
1 DCD Data Carrier Detect 8
2 RX Recieving Data 3
3 TX Transmit Data 2
4 DTR Data Terminal Ready 20
5 GND Signal Ground 7
6 DSR Data Set Ready 6
7 RTS Request to Send 4
8 CTS Clear to Send 5
9 RI Ring Indicator 22
This pinout will work on any IBM compatable computer that has a 9 pin
connector.
>I SEE THE REAR OF THE TNC HAVE A TERMINAL AS WELL AS A AUX,WHICH 1 MUST I
>USE?????
You should use the TERMINAL connection. If you have a manual for the TNC
it should all be explained in there.
>THEN DO I NEED AN EXTERNAL DRIVER SO THAT THE COMPUTER CAN SEE THE TNC AND
>WHERE CAN I FIND IT.{FOR WIN 98} ????
No! Once the TNC and computer are connected by the rs232 (serial) cable
and the correct parameters are set in the terminal program (Winpack?)
and the TNC all should work. Hope this is of some small help?
Regards and....
ÜÛÛÛÛÞ
ÚßÛÛÛÛÛÞ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
ÚÄÄÄÙ ÜÜÛÛÜ_ÜÜÜ ÛO ±± ÚÙ ....73, de Bill À¿
²²²²²²²²²²²²²²²²²²²²² ±±þ ³é G0MFW @ GB7NND.#23.GBR.EU é³
³ÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛ³ ÚÙ À¿ WinPack V6.80 Registered. ÚÙ
³ÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛ³ ±±±±±Ù ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
ÃÄÄÒÄÄÄÄÄÄÄÄÄÄÄÄÄÒÄÄÙ Ûþ\ Timed 10:14 UTC 23-Jul-2006
ß Ð Ð OßOßO (c)
Do crabs in America use the sidewalk?
Read previous mail | Read next mail
| |
