OpenBCM V1.13 (Linux)

Packet Radio Mailbox

DB0FHN

[JN59NK Nuernberg]

 Login: GUEST





  
ZL3AI  > APRDIG   03.02.03 14:27l 280 Lines 10287 Bytes #999 (0) @ WW
BID : 750-ZL3AI
Read: GUEST
Subj: TAPR Digest, Jan 19, 3/5
Path: DB0FHN<DB0RGB<OK0PPL<RZ6HXA<SP7MGD<7M3TJZ<ON0AR<ZL2BAU<ZL3VML
Sent: 030123/1040Z @:ZL3VML.#80.NZL.OC #:57976 [Chch-NZ] FBB7.00i $:750-ZL3AI
From: ZL3AI@ZL3VML.#80.NZL.OC
To  : APRDIG@WW

Subject: Re: DFing on APRS+
From: Bob Bruninga <bruninga@usna.edu>
Date: Sun, 19 Jan 2003 11:21:59 -0500 (EST)
X-Message-Number: 12

On Sun, 19 Jan 2003, Skip Allison wrote:

>I'm starting to use APRS+ for fox hunting since it's the only APRS
>program that supports DFing.
><snip>
>Other than that, the DFing on APRS+ looks great.

This is good news!  It used to be that APRSdos was the only APRS program
that fully supported all of these DFING modes:

  * DF bearing lines
    - Bearing Line Length proportional to expected area of interest
    - Beairng line Qualtiy by dottedness of line (A wedge would be better)
    - Serial intercace for Doppler DF Inc interfaces
    - Serial Interface for N7LUE DF interfaces
    - Serial interface for Roanoke and other simple DF kits
  * DF Techniques for NON Directional receiers using only your OMNI radio:
    - OMNI-DF signal contours based on received signal strneth alone
    - CAP Fade Circle Techinnque.  Simple simple 1 key mobile data entry

Maybe now that more of the windows programs support it, we can start
showing the rest of the amateur community what can really be done with
APRS DFing.  And my opinion is that 98% of what we can do is based on the
OMNI techniques which 100% of us are capable of making an input to the
tactical solution whereas only 2% of us have on-line ready-to-use
instantly BEARING taking equipment.

I admit I have not kept up with what the other programs are doing with DF,
and have heard that some dont support ANY DFing.  Couild someone in the
know and familiar with all of them, post a summary of what techniques are
supported in what programs?

Thanks

Bob

----------------------------------------------------------------------

Subject: Re: DFing on APRS+
From: "Richard Amirault" <ramirault@erols.com>
Date: Sun, 19 Jan 2003 11:28:14 -0500
X-Message-Number: 13

----- Original Message -----
From: "Skip Allison" <skipk9sa@ameritech.net>
Subject: [aprssig] DFing on APRS+

>I'm starting to use APRS+ for fox hunting since it's the only APRS
>program that supports DFing.
(snip)

AMAZING! I coulda sworn that APRSDos "supports DFing".

Oh Well ... (sigh) ... ;-)

Richard Amirault                                N1JDU                Boston,
MA, USA
www.erols.com/ramirault          "Go Fly A Kite"

----------------------------------------------------------------------

Subject: Re: Lost Manual for Yaesu/Vertex VX-150
From: Bob Nielsen <nielsen@oz.net>
Date: Sun, 19 Jan 2003 08:30:19 -0800
X-Message-Number: 14

There is also an English version of the manuals/schematics list on the
website itself:

http://hamradio.online.ru/sch_en.html

Bob, N7XY

On Sun, Aug 18, 2002 at 10:43:03PM -0500, N0ESC-APRS wrote:
> 
>>All:
> 
>Very interesting website:
> 
>Here it is in English since it seems to be full of a lot of useful
>information, only in Russian :)
> 
>http://babelfish.altavista.com/babelfish/urltrurl?lp=ru_en&url=http://hamradion
.oline.ru
>
>Michael J
>N0ESC

----------------------------------------------------------------------

Subject: Re: Next Generation TNC -- a "real" TNC, please
From: Adi Linden <adil@adis.on.ca>
Date: Sun, 19 Jan 2003 10:53:55 -0600 (CST)
X-Message-Number: 15

>The Linux version of DIGI-NET and APRS-NOS can use kernel ax.25 devices,
>which means you can (I think) get two 1200 baud TNC's out of a soundcard. Not
>bad for $10. Never used the baycom modems on linux, but if all they need is a
>serial port you'll have a couple of those as well. So a four port TNC with
>off the shelf software.

Once you need hardware DCD the soundcard modem is out of the question. The 
MIC-E thingy, where you send APRS packets at te trailing end of a voice 
transmition requires hardware DCD. 

>Hmmm..... think your missing my point. The PC *can* be the "eTNC". If you
>need rugged, then there are many many embedded PC's to chose from, some of
>them quite affordable.

Absolutely. But getting multiple interfaces between radios and PC going is 
a challange once we're talking about 4+ TNC's.

Adi

----------------------------------------------------------------------

Subject: Re: Next Generation TNC -- a "real" TNC, please
From:     Jeff King <jeff@aerodata.net>
Date: Sun, 19 Jan 2003 12:29:57 -0500
X-Message-Number: 16

Hi Art:

On Sun, 19 Jan 2003 10:53:55 -0600 (CST), Adi Linden wrote:
>>The Linux version of DIGI-NET and APRS-NOS can use kernel ax.25 devices,
>>which means you can (I think) get two 1200 baud TNC's out of a soundcard. Not
>>bad for $10. Never used the baycom modems on linux, but if all they need is a
>>serial port you'll have a couple of those as well. So a four port TNC with
>>off the shelf software.

>Once you need hardware DCD the soundcard modem is out of the question.

Are you saying the Linux Software DCD doesn't work? And the rare time's you
might need an external output, all the above named boxes support external
TNC's, so you still can have a hardware DCD.

>The
>MIC-E thingy, where you send APRS packets at te trailing end of a voice
>transmition requires hardware DCD.

These are network devices, not trackers or (most) home station devices. Now,
I can see some being used at voice repeater sites, but I can't state one way
or the other unless I research it. But in any case, there is no reason they
would not work in this application as well. A MIC-E is just a simple PIC.

>>Hmmm..... think your missing my point. The PC *can* be the "eTNC". If you
>>need rugged, then there are many many embedded PC's to chose from, some of
>>them quite affordable.
>
>Absolutely. But getting multiple interfaces between radios and PC going is
>a challange once we're talking about 4+ TNC's.

Again, this is not a Joe End User device. It takes a little bit of knowledge
about PC's, that is why I said that if you could build your own PC then you
could do this. I've already ran a version of JNOS with 8 TNC's on it... yes,
it was a bit of a challenge, but 4 TNC's or ports? That is easy.

Have you tried any of the above named applications? Do you have the need for
such a device? If the answer to both questions is not yes, not quite sure of
the point here. It will take some work to do it, but it is not a development
task, it is a administration task, which means, it has been done before and
you don't need to be a programmer to do it.

-Jeff

----------------------------------------------------------------------

Subject: Re: Next Generation TNC -- a "real" TNC, please
From: James Jefferson <jjeffers@aprsworld.net>
Date: Sun, 19 Jan 2003 11:46:35 -0600
X-Message-Number: 17

Adi said:
>Once you need hardware DCD the soundcard modem is out of the question. The
>MIC-E thingy, where you send APRS packets at te trailing end of a voice
>transmition requires hardware DCD.

You can use the soundmodem's DCD by writing some software to wiggle a pin on
the parrallel port or game port that indicates the DCD. In the userspace
soundmodem daemon (ie the new one) when you run it with the verbose flag it
will indicate when DCD is valid. Take a look at where it gets that from and
add a handler for the hardware output.

Something like:

if ( dcd ) {
   printf("Valid DCD\n");
   outportb(0x378,0x01);
} else {
   outportb(0x378,0x00);
}

That will make pin 2 (data0) on the parallel port high when there is an active
DCD. You could also use the game port in a similar manner.

Obviously there is a little bit more to it then that, but it shouldn't take
too long to implement. Then you have a nice hardware DCD line that you can
XOR with your repeater PTT and you have your MIC-E repeater.

>Absolutely. But getting multiple interfaces between radios and PC going is
>a challange once we're talking about 4+ TNC's.

Would there be any interest in a 2 to 4 port parallel port baycom modem.
Basically 4 MX-614 chips and some glue logic? Maybe a DB25 on one side, and 4
DB9 radio connectors on the other. MX614 chips are $5 a pop, so I would
imagine a four port 1200 baud modem could be made for < $50. This doesn't
exist, but perhaps it would be useful for all these next generation TNC
devices we are talking about? Something to tie to the PC/104 or desktop
computers like Jeff is suggesting?

-Jim KB0THN

----------------------------------------------------------------------

Subject: Re: Next Generation TNC -- a "real" TNC, please
From: "Andreas Junge - N6NU" <n6nu@arrl.net>
Date: Sun, 19 Jan 2003 10:00:12 -0800
X-Message-Number: 18

>>Point being, we already have 99% of what is being asked for in
>this SIG,
>>already. The missing 1% is just putting a compact flash card in
>that old PC
>>(if you have a sheltered enclosure) or putting a PC-104 board
>in a Pelican
>>case (for those that wish to float the digi in a lake), and we
>are done.

Exactly. It is just a matter of packaging. So, the BIG WIDE Digipeater in
the house/mountain top is taken care of. Put DIGI-NED on it and you can
start today. Go ahead and implement a backbone, smart routing, clipping
WIDE7-7's.

I am interested the mobile part of this thread. Look what is out there:

Transmit only :
  TinyTrack               ($35)
  PIC-E                   ($65)
  Stand-alone TNC         ($150)
  Alinco radios with TNC  ($290)

With receive + Display:

  Kenwood TH-D7A          ($400)
  Kenwood TM-D700A        ($600)
  HamHud  HUD+TNC         ($250)
  Palm/Pocket/Notebook    ($250++)

So IMHO there is a need for a device that can receive AND display packets
that fits better into our budget. The HamHud is a good beginning, but it
still requires a stand alone TNC.
Darryl Smith, VK2TDS has a device that plots position reports as Waypoints
on Garmin GPS's ala Kenwood but can not display APRS messages.

I am working - mainly for my own education - on an extension of the HamHud
principle. I used a MX614 modem chip, a 16F877 processor and a 20x4 LCD. I
can send and receive up to 128 bytes - BTW, plenty for most position
reports! I also will have a PS-2 style Keyboard connector on it to make it
easier to enter Messages.

And yes, this can be made for about $50-$60 in kit form. Now you have a
tracker that can receive - see the other thread on this on this message
board regarding this.

More ideas ?

Andreas, N6NU
Menlo Park, CA

----------------------------------------------------------------------



Read previous mail | Read next mail


 16.11.2026 13:31:42lGo back Go up