| |
DL1FDF > QRP 20.04.98 23:09l 58 Lines 2641 Bytes #-10438 (0) @ WW
BID : 204808DB0VFK
Read: DG6MS GUEST
Subj: SIERRA PWR MODS 5
Path: DB0ZKA<DB0ABH<DB0SRS<DB0SIF<DB0GV<DB0EAM<DL0EAM<DB0VFK
Sent: 980420/2042z @:DB0VFK.#HES.DEU.EU [JO41SG TheBox DG5FAU] $:204808DB0VFK
de DL1FDF @ DB0VFK.#HES.DEU.EU (Steve)
to QRP @ WW
Date: Sun, 22 Mar 1998 11:59:14 -0700 (MST)
From: marion@montana.com
To: qrp-l@Lehigh.EDU
Subject: [6585] Sierra Pwr mod
Message-ID: <199803221859.LAA02978@paw.montana.com>
Mime-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
>Date: Sat, 21 Mar 1998 12:25:36
>To: qrp-l
>From: marion@montana.com
>Subject: Sierra Pwr mod
>
> Got so many requests on this, Putting it on the list.
Change the rf choke feeding the collector of the final(L10) to a 4 to 1
impeadance ratio transformer. I used the same core material,-43, as the
original choke, but used a 0.5 instead of a .37 inch diameter core.Wind
with 12 bifiliar turns of #24 wire. Form a center tap by connecting the
start of one winding to the end of the other winding. Connect the tap to
the finals collector. Connect one of the other ends to the 12volt line and
the last lead to the input of the low pass filter. I installed in same
locationas old choke. One lead to C46 on top side left lead as viewed
from front of rig.
Center tap to hole for collector trace. Other lead to hole near C45.
IMPORTANT: installing in original position as I did requires cutting the
trace at C46 to collector, isolating C46 only.
You can use a MRF237 and sink it in original position. I used a RCA
SK9618, which has the emitter as the center leg and mouting tab.
Since the final hasemiter to ground, no insulator is needed to heat sink
directly to back of cabinet with a little heat sink paste.
There is a convenient ground at PCB
to solder emitter to, so only two leads are needed to go to base and
collector. The MRF237 will run hot, but you can beacon with the SK9618
and maybe gets warm. I used a 500ohm pot to the rear panel, to replace the
drive control as described in the Sierra manual. I notched a hole big enough
for the two wires to it to run under the board. I ran the two transistor
leads on top. You will need this control to back off of 6 to 7 watts on
160,80 and 40 meters, or to run at low current levels.
With control peaking drive
at about 90% I get 3 watts out on 10 and 15 meters and 4 watts on 20 and 30
meters. All band modules original. The SK9618 is the RCA replacement for
MRF260. Also ECG342. Same specs all around, but got SK for $4.25.
72 Roy, AB7CE
>
Reposting this as four requested.
--
qsp de dl1fdf
=========================================================================
AX25: dl1fdf@db0vfk.#hes.deu.eu | dl-qrp-ag GM | g-qrp 8769| qrp-l 252
e-mail: bauer@student.uni-kassel.de | 72 de steve DL1FDF -- DL/VY1QRP
=========================================================================
Read previous mail | Read next mail
| |