| |
PD9Q > BPQ 04.02.23 09:33l 99 Lines 2825 Bytes #999 (0) @ WW
BID : 25135_PI8LAP
Read: DJ6UX GUEST
Subj: Re: Forwarding issue
Path: DB0FHN<DB0RBS<DB0ERF<DK0WUE<DB0ZAV<CX2SA<N3HYM<IV3BVK<PE1RRR<PI8LAP
Sent: 230204/0500Z 25135@PI8LAP.#ZLD.NLD.EURO LinBPQ6.0.23
Hi Guy`s,
Sorry about that, delete the "->"
Let`s try it again :)
73 Niels
SKIPPROMPT command
Some nodes return a > at the end of their CTEXT. This could be treated as the first prompt from the BBS. You can use the SKIPPROMPT command to get round this situation.
C G8XXX-10
C G8YYY-10
SKIPPROMPT
Original Message
> R:230203/1545Z @:PE1RRR.#NBW.NLD.EURO #:9002 [Rijen] $:5499_PE1RRR
> R:230203/1542Z 5499@PE1RRR.#NBW.NLD.EURO LinBPQ6.0.23
>
>
> Hi Misko, Niels
>
> Yes, I mentioned before, the -> in PI8LAP node is causing a protocol desync
> When there is no delay, the BBS does not notice it, but when this happens:
>
> (see <======)
>
> > 230203 12:53:12 <PI8LAP HF Node PI1LAP-7
> > 230203 12:53:21 <PI8LAP PI1LAP-7 -> <=====================
> > 230203 12:53:21 >PI8LAP [BPQ-6.0.23.31-IHJM$] <==============
> > 230203 12:55:03 <PI8LAP LAPNOD:PI1LAP-7} Connected to BBS
> > 230203 12:55:03 >PI8LAP de YU7BPQ>
>
> It causes the protocol to go out of sync.
>
> The > prompt is *reserved* for BBSes. Niels, please can you remove the
> prompt from the node?
>
>
> 73
> Red
>
>
>
> On Fri, 03 Feb 23 13:05:00 Z
> YT7MPB wrote:
>
> > R:230203/1305Z @:PE1RRR.#NBW.NLD.EURO #:8995 [Rijen] $:58062_YT7MPB
> > R:230203/1305Z 17399@W9GM.#SWWI.WI.USA.NOAM BPQ6.0.23
> > R:230203/1305Z 3808@N3HYM.MD.USA.NOAM BPQ6.0.23
> > R:230203/1305Z 58062@YT7MPB.#NSD.SRB.EU LinBPQ6.0.23
> >
> >
> > Hi Niels,
> >
> > It does not work again, see bellow ...
> >
> > 30203 12:52:01 |PI8LAP Connecting to BBS PI8LAP
> > 230203 12:52:01 <PI8LAP *** CONNECTED
> > 230203 12:52:01 >PI8LAP *** linked to YU7BPQ
> > 230203 12:52:02 <PI8LAP LPTP:YU7BPQ} Ok
> > 230203 12:52:02 >PI8LAP ATTACH 4
> > 230203 12:52:02 <PI8LAP LPTP:YU7BPQ} Ok
> > 230203 12:52:02 >PI8LAP RADIO 14.10230 USB
> > 230203 12:52:03 <PI8LAP Mode and Frequency Set OK
> > 230203 12:52:03 ?PI8LAP Script MSGTYPES PTRB5000
> > 230203 12:52:03 >PI8LAP C PI8LAP
> > 230203 12:53:11 <PI8LAP *** Connected to PI8LAP
> > 230203 12:53:12 <PI8LAP HF Node PI1LAP-7
> > 230203 12:53:21 <PI8LAP PI1LAP-7 ->
> > 230203 12:53:21 >PI8LAP [BPQ-6.0.23.31-IHJM$]
> > 230203 12:55:03 <PI8LAP LAPNOD:PI1LAP-7} Connected to BBS
> > 230203 12:55:03 >PI8LAP de YU7BPQ>
> >
> > 230203 12:55:03 <PI8LAP [BPQ-6.0.23.45-B1FWIHJM$]
> > 230203 12:55:08 <PI8LAP Welcome to PI8LAP
> > 230203 12:55:08 >PI8LAP *** Protocol Error - Line should start with
> > 'F' 230203 12:55:09 <PI8LAP PI8LAP->
> > 230203 12:55:09 |PI8LAP PI8LAP Disconnected
> >
> > At my side, in the script for your system, Binary is allowed and B1 is
> > on, while B2 is off. Any idea what goes wrong?
> >
> > --
> > 73 de Misko YT7MPB@YU7BPQ.#NSD.SRB.EU
> >
> >
> >
> >
>
>
> --
> PE1RRR <PE1RRR@PE1RRR.#NBW.NLD.EURO>
>
Read previous mail | Read next mail
| |
