| |
CX2SA > SATDIG 04.07.05 08:30l 171 Lines 6780 Bytes #999 (0) @ WW
BID : 6169_CX2SA
Read: GUEST
Subj: AMSAT-BB-digest V2004 #777 4/7
Path: DB0FHN<DB0FOR<DB0SIF<DB0FHK<DB0FBB<DB0IUZ<DB0GOS<DB0RES<DK0WUE<7M3TJZ<
HS1LMV<CX2SA
Sent: 050704/0717Z @:CX2SA.LAV.URY.SA #:6169 [Minas] FBB7.00e $:6169_CX2SA
From: CX2SA@CX2SA.LAV.URY.SA
To : SATDIG@WW
Message: 12
Date: Sun, 03 Jul 2005 10:24:57 -0800
From: "Edward R. Cole" <al7eb@acsalaska.net>
Subject: Re: [amsat-bb] Re: Up and dwnlink polarization of HAMSAT
Dave,
Well, you make a common mistake (lots of folks do this, so do not feel
bad). You try to analyze polarization from only your antennas viewpoint.
It is correct when you transmit on it: If the signal rotates clockwise it
is RHCP.
But what you must ask for a signal you receive is: "what direction is the
signal rotating from the other station's viewpoint. In other words: "what
polarization does the other station have use to produce a signal your
antenna can receive? The answer for your RHCP helix is another RHCP
antenna. The exercise is to point two helical antennas at each other and
view how the signal "corkscrews" thru space. A signal leaving your antenna
must rotate clockwise as viewed from your feedpoint; a signal received by
your antenna must rotate counter-clockwise (since it is moving in the
opposite direction down the helix wire) as viewed from your feedpoint.
They still are both RHCP signals.
And if your helix is LHCP everything I said, above, reverses.
A cross yagi produces a electrical vector aligned with the first driven
element (DE) (and say for argument sake that is pointing vertical and
straight up). For the x-yagi to produce a RHCP signal the electrical
vector must point horizontal and to the right, exactly 1/4 wavelength (WL)
down the boom from the first DE. Both DE's are fed by coax cable with the
signal split and the second DE having an extra length of cable (1/4 WL
long) to properly phase the signal for CP.
Now when driven this way, the x-yagi will produce a electric vector that
rotates 90-degrees to the right (clockwise) as it travels a 1/4 WL down the
boom. (i.e. at 1/2 WL from the first DE the electric vector will point
straight down; and at 3/4 WL it will point to the left; and 1 WL from the
first DE it will again point straight up...continuing to rotate clockwise
as it travels down the boom).
Now I admit that a yagi is more complicated than this simple analysis but
the principle holds how a CP signal is generated.
I hope this helps understand this better...it helps if you have good
imagination to visualize things :-)
73's Ed - KL7UW
At 07:30 AM 7/3/05 -0700, Dave G. wrote:
>> The satellite will see the waves going towards earth in
>> clock-wize way... Now imagine the waves are comming towards
>> you (on earth), then they will be like going like
>> anti-clockwize. This seems opposite of your helical winding,
>> BUT the waves are going the other way.
>
>If my own "Rule of Thumb" is correct, the way I visualize it
>is;
>
>Starting from the helical antenna feed point, if the electron
>flow is clockwise then it is RHCP. And, viewed from the same
>feed point on the same antenna, any arriving electrons will
>travel to down the helix as LHCP.
>
>But I don't have a "Rule of Thumb" for crossed yagi's or
>diversity antennae.... they totally confuse me...
>
>Dave KK7SS
>----
>Sent via amsat-bb@amsat.org. Opinions expressed are those of the author.
>Not an AMSAT member? Join now to support the amateur satellite program!
>To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
- ----
Sent via amsat-bb@amsat.org. Opinions expressed are those of the author.
Not an AMSAT member? Join now to support the amateur satellite program!
To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
------------------------------
Message: 13
Date: Sun, 3 Jul 2005 22:28:35 +0100
From: "Graham Shirville" <g.shirville@btinternet.com>
Subject: [amsat-bb] SSETI Express July update
All work on the SSETI Express spacecraft has now been completed and the
spacecraft has left its "birthplace" - a cleanroom at the ESA ESTEC facility
in the Netherlands. The spacecraft has been packed into its special
transport container and is en-route to the launch site at Plesetsk
in Northern Russia.
The launch date is still listed as 25th August (current approx lift off is
06:50UTC but this may be corrected later) and arrangements are underway for
the launch to be shown live on ASTRA-1G - a Ku band satellite covering most
of Europe and, hopefully, these transmissions will also be streamed at both
high and low resolution on the internet.
Full details of all these media resources will be made known as soon as they
are finalised as will details of the telemetry downloading and decoding
software and the prizes being offered by ESA for the largest and also the
first contributor!
AMSAT-UK will have a team member at the launch site during the launch
campaign and intend to provide regular updates during the lead up to August
25th.
73
Graham G3VZV
- ----
Sent via amsat-bb@amsat.org. Opinions expressed are those of the author.
Not an AMSAT member? Join now to support the amateur satellite program!
To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
------------------------------
Message: 14
Date: Sun, 3 Jul 2005 16:03:00 -0600
From: "Thomas McDaniel" <tmcdanielsprint@earthlink.net>
Subject: Re: [amsat-bb] FT-847 Computer Control
Hi Simon,
I don't know exactly what you were doing with your FT-847, but SatPC32 tunes
the transmit on my FT-847 when I transmit. Using the "CAT" menu you can
step the transmit up and down in 10Hz, 100Hz or 1000Hz steps from the
computer while transmiting (I just checked to make sure). So, Yes the
FT-847 can be updated in transmit mode.
I don't know how Eric did it, but it works nicely! :-)
73 Tom n0ntx
- ----- Original Message -----
From: "Simon Brown (HB9DRV)" <simon@hb9drv.ch>
To: <amsat-bb@amsat.org>
Sent: Sunday, July 03, 2005 11:30 AM
Subject: Re: [amsat-bb] FT-847 Computer Control
> Sadly I don't think any Yaesu HF radios (except maybe the FTDX-9000) can
> be updated while you are in TX mode. So VOX or making shorts breaks may
> well be the only alternative.
>
> Simon Brown
> ---
> www.hb9drv.ch www.laax.ch
>
> ----- Original Message -----
> From: "Scott Avery WA6LIE" <wa6lie@msn.com>
>
>
>> Simon,
>>
>> The same holds true with CAT control using HRD with my FT-857D.
>> If you run VOX with short transmissions, the rig updates when the
>> radio goes into the receive mode. It would be nice it the freqs would
>> update in TX mode.
>>
>> 73, Scott
> ----
> Sent via amsat-bb@amsat.org. Opinions expressed are those of the author.
> Not an AMSAT member? Join now to support the amateur satellite program!
> To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
- ----
Sent via amsat-bb@amsat.org. Opinions expressed are those of the author.
Not an AMSAT member? Join now to support the amateur satellite program!
To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
Read previous mail | Read next mail
| |