|
G8MNY > TECH 07.08.20 07:31l 53 Lines 2609 Bytes #999 (0) @ WW
BID : 534_GB7CIP
Read: DJ6UX GUEST OE7FMI
Subj: Reducing Lamp Surge
Path: DB0FHN<DB0RBS<DB0ERF<IZ3LSV<IW8PGT<LU4ECL<JE7YGF<JH4XSY<N3HYM<CX2SA<
PE1RRR<GB7CIP
Sent: 200807/0624Z @:GB7CIP.#32.GBR.EURO #:534 [Caterham Surrey GBR] $:534_GB7C
From: G8MNY@GB7CIP.#32.GBR.EURO
To : TECH@WW
By G8MNY (Updated Sep 18)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
On an Over Head Projector I have used this surge limiter to greatly reduce the
chance of 250W lamp failure at turn on. This circuit is suitable for most low
voltage lamp systems.
high current
relay contact VOLTS COLOUR
\ 24 ¿ _..--ÄÚ White
ÄÄÄÄÄÄÄÂÄÄÄß ÀÄÄÂÄÄÄÄÄÄÂÄÄÄÄÄÄÄ¿ 21 ´ Ý ³
³ ³ ³ ³ 20 ´ Þ Ã Yellow
Lamp ³___1R5__³ Rstart ³ 18 ´ .úÙRelay ³
Supply 50W _³_ ³ 15 ´ . Operates à Orange
Diode \_/ LAMP 12 ´ . ³
e.g. ÚÄÄÄÄÄÄÄ´ ³ 9 ´ / ³
24V +³ ÚÄÄÄÄÁÄÄÄÄ¿ ³ 6 ´ .' Ã Red
@ 12A 100u === ³12V Relay³ ³ 3 ´.ú' ³
16V ³ ÀÄÄÄÄÂÄÄÄÄÙ ³ 0 ÅÄÄÄÂÄÄÄÂÄÄÄÂÄÄÄÂÄÄÁÄ>TIME
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÙ 0 1 2 SECONDS
The delay time is really nothing to do with Rstart value, Diode & the 100uF,
but the lamp temperature, as that determines the lamp resistance & hence the
voltage drop across the surge limiting 50W R. This means the turn on delay is
reduced if the lamp is already hot.
The 1R5 is made from several wire wound resistors to give the short term power
dissipation or resistance wire wound on an a large former. The value is chosen
to let the lamp get to a good orange to yellow colour temperature before the
relay applies full power. Care must be taken for the location of this resistor
& near any fanned air flow is useful.
The value of Rstart (eg. 5-100R) determines the "turn lamp on voltage" for the
relay, it may need to be a power resistor if the relay is not sensitive.
e.g. to find Rstart 24V = 33V Peak, so for 15V max across C + relay, is has to
drop 18V @ 50Hz Pulse (1/4 time) as it the same current as the relay takes!
So with no pulse currents, Rstart = 18/12 x relays (e.g. 1.5x relay) Ohms!
But with the pulse currents, Rstart = 1/4 of 18/12 x relays (0.3x relay) Ohms.
This would be a good starting point, but the relay may operate at 8V, or less
so select a higher Rstart!
Check the relay & cap get a suitable voltage when the lamp is on. The 100uF Cap
stops the relay humming @ 50Hz by smoothing the applied voltage.
Why don't U send an interesting bul?
73 De John, G8MNY @ GB7CIP
Read previous mail | Read next mail
| |