OpenBCM V1.13 (Linux)

Packet Radio Mailbox

DB0FHN

[JN59NK Nuernberg]

 Login: GUEST





  
G8MNY  > TECH     25.11.19 11:35l 55 Lines 2153 Bytes #-2546 (0) @ WW
BID : 95614_AA6HF
Read: DJ6UX DL9YCC OE7FMI GUEST
Subj: Mono Stable Revisited
Path: DB0FHN<DB0FFL<OE5XBL<F1OYP<F1OYP<F3KT<OK0NBR<IR2UBX<DB0RES<WA7V<
      AA6HF<N2NOV<N3HYM<GB7CIP
Sent: 191104/1024Z @:GB7CIP.#32.GBR.EURO #:28680 [Caterham Surrey GBR]

>From g8mny%gb7cip.#32.gbr.euro@n2nov.ampr.org Mon Nov  4 05:27:47 2019
Received: from n2nov.ampr.org by n2nov.ampr.org ([JNOS]) with SMTP
	id AA821143 ; Mon, 04 Nov 2019 05:27:47 EST
Message-Id: <28680_gb7cip@n3hym.bbs>
>From: g8mny@gb7cip.#32.gbr.euro
X-JNOS-User-Port: Circuit  (CRGWAY:GB7CIP-5 N3HYM)  -> Sending message

From: G8MNY@GB7CIP.#32.GBR.EURO
To  : TECH@WW

By G8MNY                                      (Updated Sep 18)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)

I needed a timer to timeout a 0V ON signal, on a Tx after a few minutes for RDS
Trafic flag. I had done it before with a 555 timer & input & output
conditioning inverters, all far too complex really. So I had a re-think on the
basic 2 transistor circuit, & came up with this simple junk box design.

A simular circuit can be used on PTT line of most Tx to limit key up time!

+5-20V >컴쩡컴컫컴컴컴컴컴컴컴컫컴컴컴커
         10k   �              33k     1k
          �   2M2              �      _�_
          �    쿝              �  LED=\_/      Time  
          �    �          BC337쳐�     쳐컴컴�>Limited
Low       � +  �           T1�/  �   �/BC337   Low Output
Input >컴컨캑쳐좔10K컫컴�>쳐캑   읕컴� T2
          C 100u    ===  *   �\e     �\e 
                  u1 �         �       �
0V >컴컴컴컴컴컴컴컴컨컴컴컴컴컨컴컴컴컨컴컴컴>

With no input, T1 is on & T2 held off. The 33k must be low enough to get 0V out
of T2 with required load, & the 2M2 must be low enough for T1 to turn off T2.
Higher gain transistor like the BC109c (Beta = 900) can be used for T1 with R
of 10M� for longer times, if the cap C is realy low leakage.  

With the input low, a negative voltage equal to the power rail, is appled to
T1's base & diode, holding it off for around 200 seconds. The CR time constant
of 2M2 with the 100uF cap sets the time, but a leaky C will only shorten the
time slighty in this circuit.

T1s Base 10K & u1 give basic false pulse/RF imunity.

On 5V the diode (* 1N4148) can be omitted as it is not needed to protect T1's
base from going too negative & damaging T1.



Why Don't U send an interesting bul?

73 De John, G8MNY @ GB7CIP





Read previous mail | Read next mail


 17.11.2026 01:57:47lGo back Go up