| |
G8MNY > TECH 09.08.13 14:35l 62 Lines 2100 Bytes #999 (0) @ WW
BID : 32380_GB7CIP
Read: DK3UZ GUEST OE7FMI
Subj: ALC line for Drake L-4B PA
Path: DB0FHN<OE2XZR<OE5XBL<F1OYP<SR1BSZ<ON4HU<IW0QNL<JH4XSY<JE7YGF<JS1FVG<
JH9YMQ<VE3UIL<GB7MAX<GB7VLS<GB7CIP
Sent: 130809/0946Z @:GB7CIP.#32.GBR.EU #:32380 [Caterham Surrey GBR] $:32380_GB
From: G8MNY@GB7CIP.#32.GBR.EU
To : TECH@WW
By G8MNY (Updated Mar 12)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
旼컴컴컴컴컴컴컴컴�
넬컴커 _ _ 넬컴컴컴커
냅컴켸 (_) (_) 납 �
넬컴커 _ 납 �
냅컴켸 (_) � 膨� �
� o [|]납 �
읕쩟컴컴컴컴컴컫쩡牡쩟컴컫쬔
THE PROBLEM
The output is designed for a valve Tx, where the load impedance & voltage are
much higher than for my IC735 which has larger cap on the ALC line. This causes
the ALC to be too slow, & hence give bad audio reports. The use of the PA's ALC
is desirable as there is an easy power adjustment on the PA's On/Off Volume
control PTT switch.
L I N E A R A L C C I R C U I T
ALC o)컴1k컴쩡�1k캑>쳐쩡컴쩡캑쳐컴�<Cathode
-20V === � � 47pF RF Drive
into �5nF 15k ===
1M�// � � �47pF
1nF 컴컴컴좔컴컫컴컴)컴컨컴컴컴컴�
PTT SW � �
& LEVEL 100k<켸
POT 읕컴컴+120V Bias
This problem may occur with many Valve PAs driven from modern rigs!
MY CURE
I added a high impedance 2:1 attenuator to reduce the voltage into a PNP
transistor emitter follower, (the resistors are located at transistor base as
RF stoppers). It is powered by an negative rail derived from relay supply.
N e w E x i s t i n g c i r c u i t
ALC o)컴1k커 旼컴컴컴컴컫컴1k캑>쳐쩡컴쩡캑쳐컴�<Cathode
-10V e\� 100k === � � 47pF Drive
1k� PNP쳐컴� �5nF 15k ===
Source /� 100k � � �47pF
� +쳐컴컴컴컴컨컴컴쩡컴�)컴컨컴컴컴컴�
18V � === 100k<켸
AC컴100캑<쳅컴컴켸100uF LEVEL
1N4001 (-25V) 읕컴컴+120V Bias
RESULTS
I have good audio reports now, & at the touch of the PA's PTT/ALC control I can
control if the PA is in or out, & the power level, which makes tunning up much
easier.
See my Tech bul on "PTT line for Drake L-4B PA" & "Power Factor of Drake
L-4B PA"
Why Don't U send an interesting bul?
73 de John, G8MNY @ GB7CIP
Read previous mail | Read next mail
| |