OpenBCM V1.07b12 (Linux)

Packet Radio Mailbox

DB0FHN

[JN59NK Nuernberg]

 Login: GUEST





  
G8MNY  > TECH     07.07.06 11:19l 127 Lines 6021 Bytes #999 (0) @ WW
BID : 37358_GB7CIP
Read: DL1LCA GUEST
Subj: Rotator Kenpro KR400rc info
Path: DB0FHN<DB0FOR<DB0SIF<DB0EA<DB0RES<ON0AR<GB7CIP
Sent: 060707/0904Z @:GB7CIP.#32.GBR.EU #:37358 [Caterham] $:37358_GB7CIP
From: G8MNY@GB7CIP.#32.GBR.EU
To  : TECH@WW

By G8MNY                                                (Updated Nov 05)  
(8 Bit ASCII Graphics use code page 437 or 850)
This is a reliable rotator with manual L & R switches & servo motor driven 
heading 360ø readout. It is simular to several ranges of models offered by
different makers. 
 ____________________                    /ºº\  Stub Mast
³   .-"~"-.   ³      ³~-._              ³ ºº ³ Clamp Castings
³ /'   |   `\ ³   ²  ³   ³            __³_ºº_³__
³|     |     |³      ³   ³           ³          ³
³³     "     ³³      ³   ³  5 Wire   ³__________³ ROTATOR
³ \         / ³      ³   ³   Cable    ³________³  
³  `ú.___.ú'  ³[-][-]³ _.|              ³ ºº ³  À option flat
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÁ~         Support ³ ºº ³     base plate
   CONTROLLER                  ast Clamp \ºº/


DIAGRAM             __
                  /Dial\
           oÄÄÄÄÄ´Motor ÃÄÄÄÄo1
           ³      \.__,/     ³  Dial
           ÃÄÄÄÄÄÄÄÄÄÄÄÄ´ÃÄÄÄ´  Motor
       2   ³  D1       C1    ³  Drivers
       ÚoÄÄ)Ä´>ÃÄÂÄÄÂÄÄÄÂÄÄÄ)ÄÄÂÄÄÄÄÂÄÄR5ÄÄÂÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ+13V
       ³   ³ ³    ³ ===  ³   ³  ³    R3    _³_   ===C5
       ³   ³ ³    ³  ³C4 ³   ³   \³  ³   D7\_/,  _³_                 SERVO
       ³   ³ À´<ÃÄ)ÄÄ´   ³   ³    ÃÄÄ´  13v_³_  ////                 LOOP
       ³   ³  D2  ³  ³   ³   ³  e/³  ³    ////         «Q4           GAINÚÄÄÄ>
       ³   ³      ³  ³   ³   ³  ³   _³_D5              ,/3ÃÄÄÄÄÄÂÄL1ÄÄÄ>VR1
       ³   ³      ³  ³   ³   ³  R1  \_/  ÚÄR7ÄÄÄÂÄR9ÄÂ<1  ³    ===       ÃÄÄÄ>
    14V³   ³      ³  ³  ===  ³  ³    ³   ³      ³    ³ `\2ÃÄ¿  _³_C7     ³
     º(    ³Bridge³  ³   ³C2 ³  ³    ³   ³ ,/2ÃÄÙ    ÀÄR11ÄÄ´ ////       ³
     º(    ³ Rec  ³  ³   ³   ÀÄÄ´    ÃÄÄÄÁ<6  ³Q3          R13  Balanced ³
     º(____o___   ³  ³   ³      ³    ³     `\3ÃÄ¿    ÚÄR12ÄÄ´ Comparitor ³
     º(   ³   _³_ ³  ³   ÃÄÄÄ¿  ³   _³_         ³    ³ ,/6ÃÄÙ            ³
Powerº(   ³  //// ³  ³   ³  _³_ R2  \_/D6       ÃÄR10Á<7  ³              ³
o/ o¿º(  (B1)     ³  ³   ³ //// ³e   ³          ³      `\5ÃÄÄÄÂÄÄÄL2ÄÄÄÄÄÙ
    )º ³  ³    D3 ³  ³   ³       \³  ³         R8     «Q4    ===  RFI
    )º ³  ³ ÚÄ´>ÃÄÙ  ³  ===C3     ÃÄÄ´         _³_         C8_³_ filter
    )º ³  ³ ³    D4  ³   ³       /³  R4       ////          ////
 1A )º ÀÄÄoÄÁÄ´<ÃÄÄÄÄÁÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÁÄÄR6ÄÄÂÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ -13V
ÄoÄoÙº    3                                _³_   ===C6
Fuse º                                  D8 \_/,  _³_
     º                                  13v_³_  ////
     º                                    ////                5ê
     º _______________________o\ o___________________* 5 *___())))___
     º(                      ____o RIGHT   ³                 MOTOR   ³
     º(                     ³             === C12          WINDINGS  ³
     º( 26V                 ³_o\ o_________³_________* 4 *___())))___³
     º( 2A                       o LEFT                       5ê     ³
     º(______________________________________________* 6 *___________³
                                          Motor Common

+13V ÄÂÄÄÄÄÄÄÄÄR14ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
      ³                           ³     8
      ³                        ÚÄÄ)ÄÄÄÂÄÄoÄÄÄÄ¿
 <ÄÄÄÄ)ÄR15ÄÂÄÄÄÄÄÄÄÄÄÄ¿       ³  ³  R23 ÚÄÄ>RV3
VR1   ³     ³          ³       ³  ³   ³  ³    ³CAL
 <ÄÄÄÄ)ÄÄÄÄÄ)ÄÄÄÄÄÄÄÄÄÄ)ÄÄÄÄÄÄÄ)ÄÄ)ÄÄÄ)ÄÄo15  ³
      ³     ³          ³       ³  ³   ³       ³       RESISTANCE
      ³     ³          ³   ÚÄÄÄ´  ³   ÃÄÄÄoÄÄÄÙ         BRIDGE
      ³     ³          ³  R21 VR2 ³  R24   9   DIAL
      ÃÄÄÄÄÄ)ÄÄÄÄ¿     ³   ÀÄÄÄ´  ÀÄÄÄÁÄÄoÄÄÄÄ>VR4
      ³     ³    ³     ³       ³          7    ³500ê
      ³    R16   ³     ³       ³      10       ³
      ³     ³   R18    ÀÄÄÄÄÄÄÄ)ÄÄÄÄÂÄÄoÄÄÄÄÄÄÄÙ
     ===     \³  ³ Current     ³   R25                     ROTATOR
    C9³    Q5 ÃÄÄ´ Limiter    R22   ÀÄÄÄoÄÄÄÄÄÄÄÄÄÄÄÄÂ* 2 *ÄÄÄ>VR5
      ³     e/³   \³  C10      ³         6           ³         ³500ê
      ³     ³   Q6 ÃÄÄÂÄR19Ä¿  ³                 C11===        ³
      ³     ³    e/³ ===    ³  ³     5               ³         ³
-13V ÄÁÄÄÄÄÄÁÄÄÄÄÁÄÄÄÄÁÄR20ÄÁÄÄÁÄÄÄÄÄÄoÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁ* 3 *ÄÄÄÄÙ

     o = Internal PCB wiring points          * = External Terminals


COMPONENT
No   R    |  No    R      C      D        Q      VR    L       B
13  10k   |   1   220    10n  1N4002  2SC1815   20k  220uH  14V Bulb
14   1k   |   2   220   100u  1N4002  2SA1015   20k  220uH
15   1k   |   3   10k   100u  1N4002  LM 741    10k
16  390   |   4   10k    10n  1N4002  NMJ4558   500
17  820   |   5   150    10n  1S1588  2SC1815   500
18  47k   |   6   150    10n  1S1588  2SC1815
19  33k   |   7  560k    10n   WZ130
20  330   |   8  560k    10n   WZ130
21  10k   |   9   10k   100u
22   1k   |  10   10k    10n
23  820   |  11  150k    10n
24  5k6   |  12  150k   100u AC
25   2

Common faults.. 
I have seen on more than one occasion, a split in the plastic pinion on the DC
dial motor. This causes the dial hunting as the display servo can't find the
matching dial pot balance. The cure is to remove the motor carefully slide the
pinion off. Roughen up the D shaped shaft, & using a resin glue, glue back on
the pinion, maintaining pressure across the crack until the glue has hardened,
then reassemble & test.

A problem Bryan G6ODE found was a loose pinion gear on the motor shaft in the
rotator.

Another problem Brian G8VPR mentions is the Rotator Pot going open circuit, so
here is the circuit to help do tests...

MODIFICATIONS
I use mine for /P work & have done some mods...

1/ Add a 22ê in series with the lamp, to improve lamp lifetime.

2/ Add an 8ê 10W in series with motor common (*6*), to reduce super saturation
   of the motor. It can work ok with 18V with hardly any loss of torque, & for
   much longer before the motor catches fire.
 
3/ Add a 0.47uF 300V AC across the 240V mains I/P to Power Factor correct the
   permanent transformer load.

4/ Keep the pointer screw just loose enough for manual direction adjustment.


Why don't U send an interesting bul?

73 de John G8MNY @ GB7CIP


Read previous mail | Read next mail


 17.06.2024 23:32:27lGo back Go up