OpenBCM V1.13 (Linux)

Packet Radio Mailbox

DB0FHN

[JN59NK Nuernberg]

 Login: GUEST





  
ZL3AI  > APRDIG   11.02.03 05:47l 260 Lines 9006 Bytes #999 (0) @ WW
BID : 879-ZL3AI
Read: GUEST
Subj: TAPR Digest, Feb 07, 1/1
Path: DB0FHN<DB0RGB<OK0PPL<RZ6HXA<IK1ZNW<IR0NET<EB4BCS<WA7V<ZL2TZE<ZL3VML
Sent: 030209/0740Z @:ZL3VML.#80.NZL.OC #:59104 [Chch-NZ] FBB7.00i $:879-ZL3AI
From: ZL3AI@ZL3VML.#80.NZL.OC
To  : APRDIG@WW

TAPR APRS Special Interest Group Digest for Friday, February 07, 2003.

1. Re: Rand Mc Streetfinder GPS
2. Re: Etrex and Low temps
3. Weather Display and <0 temps
4. Re: PCsat NORMAL OPS soon
5. Weather station for fire command
6. Re: Rand Mc Streetfinder GPS
7. Re: Weather station for fire command
8. WebUpdateWX2.1 available
9. re: aprs spec/words of warning
10. Re: Rand Mc Streetfinder GPS
11. Problem with HIN202 (rs232 part)

----------------------------------------------------------------------

Subject: Re: Rand Mc Streetfinder GPS
From: roger w rockwell <wb4trz@juno.com>
Date: Thu, 6 Feb 2003 23:16:40 -0600
X-Message-Number: 1

Anyone here using the Rand McNally Streetfinder GPS for the PalmIII ??  I
haven't used mine for a long time and cannot remember which is the
correct wall wart to charge the GPS batt.  I've got about 4 that will
plug into it but they range from 3v to 13v out.  I don't want to burn the
thing up.  So, if anyone knows the correct voltage please let me know.
Thanks
Roger 
K1PNS

----------------------------------------------------------------------

Subject: Re: Etrex and Low temps
From: Chris Rose <kb8uih2@chartermi.net>
Date: Fri, 07 Feb 2003 07:31:46 -0500
X-Message-Number: 2

Greetings,
I leave my Garmin 12 plugged in and turned on all the time and have for 
about 1 1/2 years with either a THD7 or now the D700 and have had only a 
few hiccups with regard to locking on sats as my only complaint.  I got 
the error message that I had to restart or reinitialize the GPS.  I just 
turned it off and back on and it did what it was supposed to do.  It has 
been through winters and summers.

Central Lower Michigan.

73,
Chris
KB8UIH

----------------------------------------------------------------------

Subject: Weather Display and <0 temps
From: Dave Kaplan <dkaplan@steffeninc.com>
Date: Fri, 07 Feb 2003 07:11:37 -0600
X-Message-Number: 3

My <0 temps are not reporting right on FindU.

I e-mailed Steve and, checking the raw data, he found I was sending 
improperly formatted data. Weather Display is sending -t008 when it should 
be sending t-08.

Is anyone else having this problem?

I have e-mail Brian Hamilton and asked him to check his program. It worked 
last month when the temps were below zero, but I've upgraded software 
versions of Weather Display since.

Dave

----------------------------------------------------------------------

Subject: Re: PCsat NORMAL OPS soon
From: Alex <kr1st@amsat.org>
Date: Fri, 07 Feb 2003 08:23:29 -0500
X-Message-Number: 4

Bob Bruninga wrote:

>This will cease as soon as one of the cells shorts or reverses, so use her
>while you can, she wont last long...  (knock on wood)....

Let me throw in a really dumb question. Why is this condition allowed to
occur on a satellite? I'm not talking specifically about PCSAT, but any
such satellite. 

Couldn't a watchdog circuit (not necessarily electronic, but maybe
chemical, or perhaps even (semi-) passive) be added so that if this
condition occurs, then the batteries will be disengaged or switched to a
fresh set, or solar only? I'd think that it is a highly undesireable
situation that a sattelite becomes uncontrollable just because (one of)
the power sources gives up. I'm not a space expert so it may be just
foolish talk I'm uttering here.

73,
--Alex KR1ST

----------------------------------------------------------------------

Subject: Weather station for fire command
From: "Dakota Summerhawk" <dakotas@hotpop.com>
Date: Fri, 7 Feb 2003 10:41:35 -0700
X-Message-Number: 5

I have been looking at the ability to provide weather (real time) for fire
command. My question will the Paccomm pico with second port accept data from
a one wire station? I know the second port on the pico is a rs232 but will
it accept data from another source besides GPS?
Let me know.
Thanks
Peter N0WRE

----------------------------------------------------------------------

Subject: Re: Rand Mc Streetfinder GPS
From: Roger Grady <k9opo@comteck.com>
Date: Fri, 07 Feb 2003 13:41:42 -0500
X-Message-Number: 6

At 11:16 PM 2/6/03 -0600, roger w rockwell wrote:
>Anyone here using the Rand McNally Streetfinder GPS for the PalmIII ??  I
>haven't used mine for a long time and cannot remember which is the
>correct wall wart to charge the GPS batt.  I've got about 4 that will
>plug into it but they range from 3v to 13v out.  I don't want to burn the
>thing up.  So, if anyone knows the correct voltage please let me know.

That's why I put labels on my wall warts! :-)

The one that says "Palm GPS" is labeled 12vdc, 300ma, 3.6VA, center pin
positive.

Roger Grady  K9OPO

----------------------------------------------------------------------

Subject: Re: Weather station for fire command
From: "Mike Yetsko" <myetsko@insydesw.com>
Date: Fri, 7 Feb 2003 15:17:56 -0500
X-Message-Number: 7

>I have been looking at the ability to provide weather (real time) for fire
>command. My question will the Paccomm pico with second port accept data from
>aone wire station? I know the second port on the pico is a rs232 but will
>it accept data from another source besides GPS?
>Let me know.
>Thanks
>Peter N0WRE

Well, the 'OneWire' isn't something that can 'stream' out data to be
'accepted' by anyone.  You have to 'interactively interrogate' the unit.
And things like the wind speed aren't.  What you get from the OneWire
is a count of revolutions.  You read it.  Then you read it later.  Wind
speed is proportional to the difference in counts per the difference in
time.  The wind direction is just as complex.  You read 4 A/D channels,
and depending on the state of the 4 channels (at 0, .5, or 1 times the
OneWire bus voltage, you can determine where out of 16 possible
(at 22.5 degree spacing) the arrow is pointing.

Mike

----------------------------------------------------------------------

Subject: WebUpdateWX2.1 available
From: "Pat Karp" <pkarp@conwaycorp.net>
Date: Fri, 7 Feb 2003 14:36:56 -0600
X-Message-Number: 8

You can download it at http://karpfamily.net and click on the My software
link.

Other than a new look I have added the ability to download any file from a
website.  You can download just the update if you already have WebUpdateWX
installed.  To update WebUpdateWX download the file and extract it into the
directory you installed WebUpdateWX.  If you wish to do a complete install
then make sure you remove any previous installations by going into the
control panal - add/remove software.

Pat

----------------------------------------------------------------------

Subject: re: aprs spec/words of warning
From: "Wes Johnston" <wes@johnston.net>
Date: Fri, 7 Feb 2003 16:08:45 -0500
X-Message-Number: 9

I've been thinking a little (not too much though)....

what is the difference between UI frames and UDP packets?

In UI we use WIDEn-n
In UDP we use TTL (time to live).

In UI we use digipeaters
In UDP you can spec a GATEWAY

Neither packet type is acked.

I haven't studied up on it yet, but can't you just send broadcast packet to
every station by sending it to x.x.x.255 ?  I'm thinking that UDP (the
subset of TCP/IP) may be the way to go here...

If we used a packet type like TCP or UDP, we have this 'little thing' called
internet which is already set up to route packets for us.

Wes

----------------------------------------------------------------------

Subject: Re: Rand Mc Streetfinder GPS
From: roger w rockwell <wb4trz@juno.com>
Date: Fri, 7 Feb 2003 15:13:43 -0600
X-Message-Number: 10

That's why I put labels on my wall warts! :-)

Ya, I do to now.   I started labels about a year ago but have about a
dozen pre-label days. I bought the brother Home and Hobby III just for
that purpose.  Thanks again.

----------------------------------------------------------------------

Subject: Problem with HIN202 (rs232 part)
From: "Mike Yetsko" <myetsko@insydesw.com>
Date: Fri, 7 Feb 2003 18:29:44 -0500
X-Message-Number: 11

I'm using a HIN202 part in an interface and am having a bit of an issue.

This is one of the 'all in one' RS-232 interface parts.  You just connect
4 caps (0.1uf each) and provide 5V and you have 2 channels each 
way for RS-232 and TTL.

Anyway, there are two pins, V+ and V-.  These are NOT Vcc.  These 
are for the internal charge pumps to generate the +9 and -9 volts.

I saw an app that said tie a 0.1uf from V- to ground, and another one 
from V+ to ground.  I built up the circuit with DIP parts and it worked
fine.  However, I laid a board out for SMT parts, and it hangs on initial
poweron about 50% of the time with a high current condition of the 202.

Now, I can solve that by taking the cap from V+ to ground and instead
placing it from V+ to 5v.  (Which I happened to see on yet another 
schematic example.)  

While I'm upset my board isn't 'right', I'm also wondering why?  It's an
easy change.  I can just flip the two surface mount caps on edge and use
a piece of wirewrap...  But I'm still wondering why...

Mike

---

END OF DIGEST


Read previous mail | Read next mail


 16.11.2026 02:26:04lGo back Go up