| |
ZL3AI > APRDIG 24.12.00 19:04l 217 Lines 7812 Bytes #999 (0) @ WW
BID : 35136_ZL3AI
Read: GUEST
Subj: TAPR Digest, Dec 18, 2/10
Path: DB0ABH<DB0CWS<DB0ROF<DK0MNL<DF0HMB<DB0HES<OZ7BOX<OZ2DIZ<7M3TJZ<LZ3NP<
PY2DML<F5TMZ<F5TMZ<GB7GUR<ZL2BAU<ZL3VML
Sent: 001218/2314Z @:ZL3VML.#80.NZL.OC #:51010 [Chch-NZ] FBB7.00g25 $:35136_ZL3
From: ZL3AI@ZL3VML.#80.NZL.OC
To : APRDIG@WW
> You want TF21c.ZIP, which is TNC1 command mode software that supports both
> AX.25 version 2 and can go into KISS mode.
Even though Simtel says this is for the TNC1, it appears to be for the TNC2.
This one is for the TNC1 (But doesn't have kiss)
ftp://ftp.ucsd.edu/hamradio/packet/wa8ded/
Sorry
Jeff
----------------------------------------------------------------------
Subject: Re: 9600 Baud Cxxx
From: Mark Fellhauer <sparkfel@primenet.com>
Date: Mon, 18 Dec 2000 01:57:10 -0600
X-Message-Number: 7
At 11:00 PM 12/17/00, Jeff King wrote:
> Paccomm offered a integrated 9600bps ham package in the late
>80's until recently.... Kantronics had a plug and play 9600/19200 solution in
>the early 1990's....
Let us not forget the ill-fated Drake TR-270. Did anyone ever buy one?
73,
Mark
KC7BXS
----------------------------------------------------------------------
Subject: 9600 BPS? We don't need no steenkin' 9600 BPS
From: Mark Fellhauer <sparkfel@primenet.com>
Date: Mon, 18 Dec 2000 02:49:35 -0600
X-Message-Number: 8
http://www.wa4dsy.net/
Of course, it looks like the PI2 interface card is out of production.
----------------------------------------------------------------------
Subject: Re: Changeing callsign in APRSdos
From: "lloyd mitchell" <lloydm75@hotmail.com>
Date: Mon, 18 Dec 2000 05:46:29 -0500
X-Message-Number: 9
aprsxxx /new
xxx = version #
Lloyd KD4HTW
----Original Message Follows----
From: "Stephen M. King" <frastephen@home.com>
To: "TAPR APRS Special Interest Group" <aprssig@lists.tapr.org>
Subject: [aprssig] Changeing callsign in APRSdos
Date: Mon, 18 Dec 2000 01:10:30 -0500
I have APRSdos on my main computer and I would like to add a ssid to my
call. How do I change the callsign? I guess (because of validation) I
would need to re-enter all the initial settings (which is fine), but how do
I force it to allow me to do that????
Thanks in advance for the help!
73,
Stephen
KD3OG
---
You are currently subscribed to aprssig as: lloydm75@hotmail.com
To unsubscribe send a blank email to leave-aprssig-18700I@lists.tapr.org
Questions regarding the SIG go to the SIG administrator: wa1lou@tapr.org
----------------------------------------------------------------------
Subject: Re: 9600bps radios, was Re: APRS Satellite Details
From: <henk.de.groot@hetnet.nl>
Date: Mon, 18 Dec 2000 12:52:20 +0100
X-Message-Number: 10
> Maybe the Europeans who have a lot more practical experience with
> 600 baud would care to comment on the sensitivity of typical "good
> quality" 9600 baud implementations... Even the USA packet folks I
> have spoken with have said that their experience with 9600 baud is
> worse than 1200 over the same path, power, and antennas.
I don't have measurement data but I can give some experience data.
On the HAM network 9600 baud is generaly much worse than 1200 baud. You =
need in general very strong signals. This to not due to the mode itself =
but due to the very simplified equipement used by HAM operators.
Contributors are:
- Transmitted wave-forms are often already distorted before comming on =
air due to non linearities in the modulator. On Japaneese equipment an =
aditional problem is that the PLL tries to correct the low frequency =
components - it things that the VCO is wandering off-frequency when in =
fact a 10 Hz component in the signal.
- Filters characteristics used in HAM equipement are not optimized for =
DATA, they are not flat enough or have group-delay problems that distort =
the signal.
- Receivers are often modified to take the received signal directly from =
the modulator. Especially at that start of the reception there is a =
DC-jump on the output if the receiver is not exactly in the frequency of =
the transmitter. Propper adjustment of the receiver to the transmitters =
frequency is vital.
These 3 points can be fixed by using a tranciever designed for DATA =
(like the TEKK or Eisches LinkTRX III used for 23cm 19200 baud =
interlinks). But that is not the end of the story and the problems with =
HAM equipement.
Most decoders used by HAMs for FSK to digital decoding are very basic =
and simple slicers, this includes the original G3RUH modem. If the =
signal is above the frequency its a '1', if it is below its a '0'. The =
slicers are only kept in the middle of the signal by averiging the =
signal (just a simple capacitor coupling). The only a little bit more =
advanced hardware solution I've seen is in the OE5DXL modem, which uses =
a trick with 2 diodes and 2 capacitors to home-in on the signal quicky =
(but is more sensitive to signal noice as a drawback).
For these simple decoders it means that inter-simbol interference, group =
delay and multipath signals have a devistating effect on the ability to =
decode signal. A lot could be saved by using a coherent or semi-coherent =
decoder. Commercial systems like GSM, D-AMPS and PCS don't use anything =
else than that. Adjusting the HAM equipment is often done using the "eye =
pattern" for maximum "eye opening", thats the only means there is.
The only impovement I've seen so far in decoding technique is the effort =
by Tomas Sailer, HB9JNX, to use the sound-card. He attempts to build a =
decoder that predicts some of the low-order distortion and compensate =
before a decoding attempt is made. I expect this decoder will decode =
signals long after all other modems already gave up. Of course the =
penalty is the need for some heavy signal processing which you don't =
have available in a TNC of Handheld device. There is an interesting =
article about it in this years DCC proceedings.
I don't know what the TH-D7 uses, but I expect it is a slicer too. I =
don't know if there are any specific measures to take care of the =
voltage jump out of the decoder when the reciever is not exactly on the =
same frequency as the sender. For satelite one would expect this since =
the frequency of the sattelite constantly changes due to doppler shift. =
A huge advantage is that the sattelite signal is most likely a very =
clean, well modulated signal, unlike the terestrial HAM 9k6 stations.
Anyway, I think due to the equipment we use as HAMs (and not because of =
the theoretically accievable performance) the 9600 signal needs to be a =
lot stronger then a comparible 1200 baud signal needs to be. It could be =
a lot better, but HAMs just cannot afford it.
By the way, I'm using a modified car-phone for my 9k6 needs (picture =
http://home.iae.nl/users/vhaaften/nokia/) and a YAM modem =
(http://www.microlet.com) which I modified with the detection method =
"stolen" from the OE5DXL modem (http://www.raag.org/sv2agw/oe5dxl.zip).
Kind regards,
Henk.
----------------------------------------------------------------------
Subject: Re: APRS demo for Sheriff's department
From: Kd4emi@aol.com
Date: Mon, 18 Dec 2000 10:01:34 EST
X-Message-Number: 11
Give me a private email today and I'll get with you.
I can describe my experience with our Sheriff's Dept.
Mike Kantor
KD4EMI@AOL.COM
----------------------------------------------------------------------
Subject: Re: Aprs Serve
From: Guy Story <kc5goi@tapr.org>
Date: Mon, 18 Dec 2000 10:22:00 -0600 (CST)
X-Message-Number: 12
Bob, try backing up to 2.4.6 if you can. I connected to second.aprs.net
and did not receive the message. Only not having registered software
should keep you from igating, not software being out of date. 2.4.7 is
the most current version of WinAPRS. There is no reason for it to show
being out of date.
73,
Guy Story
KC5GOI
kc5goi@tapr.org
http://www.kc5goi.net
----------------------------------------------------------------------
Subject: RE: X/Y coordinates on a graphic file (was: continuous bickering)
From: David Locke <locked@intplsrv.net>
Read previous mail | Read next mail
| |