OpenBCM V1.13 (Linux)

Packet Radio Mailbox

DB0FHN

[JN59NK Nuernberg]

 Login: GUEST





  
DK8KV  > QRP      22.07.98 19:56l 113 Lines 4820 Bytes #-10344 (0) @ EU
BID : 227809DB0MKA
Read: DL6MEE DL2MHG DG6MS GUEST
Subj: SG-2020 V1.04 upd
Path: DB0ZKA<DB0ABH<DB0SRS<DB0MW<DB0AIS<DB0IZ<DB0MKA
Sent: 980722/1831z @:DB0MKA.#NRW.DEU.EU [Hennef OP:DL3OE] $:227809DB0MKA
de DK8KV @ DB0MKA.#NRW.DEU.EU   (Walter)

to QRP @ EU

IMPORTANT INFORMATION UPDATE FOR OPERATORS 
==========================================
OF THE SG-2020 HF SSB TRANSCEIVER JULY 1998
===========================================

1. 'CHIRP - A minor chirp problem on CW has been resolved with a software
    change, and all units are now fitted with this latest software 
    version, 1.04.

2. The latest software version 1.04 Code Revision is
   displayed by pushbutton Rev, depressed while powering up.

3. Location of pushbuttons:
   All four main pushbuttons:  FAST, MEM, BW, REV
   have been designed and located for convenient one-hand operation. A few
   users have complained that two hands are required and that the push
   buttons are too close. Users should become familiar with the use of
   one hand, using these push buttons and the main tuning knob.

4. Headphone:
   Some headphones are very sensitive and provide an outstanding low 
   frequency response. In this situation, we suggest use of a communications
   type headphone or an attenuator between the speaker jack and the headphone.</font> 

5. AF Amplifier "Hiss"
   No further "hiss" is noticeable in the presently produced units.
   In some situations, we found marginal AF amplifiers.

6. Fast Tuning
   Fast tuning can be set up to 10 KHz to allow extremely fast coverage 
   through the whole bands (manual page 16, paragraph 10.7).

7. Receiver CW Operation
   The SG-2020 was designed with high performance CW operation.
   To achieve best use of this unit under crowded situations, the combination
   of the 3 functions designed for this purpose will provide the user 
   outstanding performance, as follows:
   (a) BW adjustment
   (b) RF control
   (c) If interfering signals are still present, use the passband tuning
       for best rejection

8. SG-2020 for Commercial Use
   This unit is designed to allow simple operation for any casual operator.
   For example, if only 4 channels are required, enter these 4 channels 5
   times in the 20 memories and lock the unit. Now, the operator depresses
   the MEM push button and rotates the main tuning knob and only the four 
   preset channels will be accessible.
   Lockout (PBT & RIT) page 16 of manual, paragraph

9. Linear Amp SG-500
   The SG-2020 is fully compatible with our SG-500 watt amplifier.
   Expected power from 3 to 18 MHz is not less than 450 watts and not less
   than 300 on the extreme ends of the HF bands.
   Only the RF is required to control the SG-500.

10. Power On Options
    Note: Holding "CMD" upon power up will cause the 1st step to allow entry
    into the calibration routine. (The LCD will display "C".)
    Without the next key sequencing the sequence will abort to normal
    radio operation about a second after "CMD" is released.
    Supersedes page 16, paragraph 11.1

11. Backlight Default On/Off and LED Test
    An LED test sequence has been added to the backlight on/off power up
    sequence.
    (a) Power up the radio while depressing the "light" button.
        Hold it until either "dl ON" or "dl OFF" is displayed.
    (b) Select whether you want the backlight on or off when the radio is
        turned on. This is done by using the "REV" button to toggle between
        "dl ON" and "dl OFF"
    (c) Store the choice by depressing the button.
    (d) Once the "MEM" button is released, a sequential test is performed on
        each LED and the backlight.
    (e) Radio then reverts to normal operation.

12. Now, the Transmit bar graph will also work in the Iambic key mode.
    Supersedes page 17, note 2

13. Selectivity is well within the best specifications in the industry, 
    at 2.7KHz and not less than 60dB rejection on the adjacent channel.

14. IF configuration and design
    Most existing HF transceivers are designed with 2, 3 or 4 IF stages.
    Many users believe that just one IF stage (as in the SG-2020) provides
    inferior performance. Actually, the contrary is true. The less IF
    stages there are, the less receiver and transmitter spurious frequencies
    are apparent. Generally, if the design is done right, one IF stage is
    sufficient. This also provides superior receiver performance. The SG-2020
    receiver is equal or better than most transceivers available in the 
    commercial or ham markets.

15. Stress Power
    Set maximum output capability of the transceiver by setting the output
    level to "M" for maximum. With 20mV RMS AF input at the microphone
    connector are:

    Frequency Power Range

    1.8 MHz   23 to 27 Watts
    3.7 MHz   23 to 35 Watts
    7   MHz   30 to 40 Watts
    14  MHz   35 to 45 Watts
    18  MHz   30 to 42 Watts
    29  MHz   17 to 23 Watts

    The above readings are for reference and orientation only and may change
    without notice.



Read previous mail | Read next mail


 17.11.2026 16:58:17lGo back Go up