OpenBCM V1.13 (Linux)

Packet Radio Mailbox

DB0FHN

[JN59NK Nuernberg]

 Login: GUEST





  
DL4YHF > QRP      11.08.99 02:27l 315 Lines 14508 Bytes #-9959 (0) @ EU
BID : 108923DB0EAM
Read: OM2ZZ GUEST
Subj: QRP-Keyer: english manual
Path: OE1XAB<OE3XPR<OE3XBS<S50BOX<S50MBR<S50ATV<S50MBL<IV3LAV<IV3AVQ<I4UKI<
      IK2YHJ<IK2QCA<IW2FPO<HB9OK<HB9H<HB9OS<HB9EAS<OE9XPI<DB0CZ<DB0KFB<
      DB0AAB<DB0FSG<DB0PV<DB0MAK<DB0ERF<DB0NHM<DB0EAM
Sent: 990810/2047z @:DB0EAM.#HES.DEU.EU [Kassel DB8AS] LT:100 $:108923DB0EAM
de DL4YHF @ DB0EAHES.DEU.EU(Wolfgang)

to QRP @ EU

Manual and Description of DL4YHF's QRP-PIC-Keyer
------------------------------------------------

Speed Control
-------------
The CW speed is controlled by a poti, which is also active during "replay".
The speed range is about 20...300 letters per minute.

Buttons
-------
There are two buttons that control recording and replay of messages.
The button "Message 1" controls a message of about 63 characters that is
stored in the PIC's internal EEPROM. This message will not get lost even if
you disconnect the battery.
The button "Message 2" controls a message of about 55 characters that is
stored in the PIC's internal RAM. This message will get lost if the battery is
disconnected (but we never disconnect the battery as there is no need for a
power switch).
If both buttons are pressed simultaneously, the keyer switches to "command
mode" (explained below).

Playing a stored message
------------------------
A short press of a "Message"-Button starts playing the corresponding message.
If a message is "partitioned" (see below), use multiple short "clicks" of a
button to select the part of the message you want to play.

Recording a message
-------------------
To record a new message you have to press the corresponding button for about
0.5 seconds (until the keyer signals "M", which means "Message record").
To stop recording a message you touch the message button for a second time.
The keyer will signal "S" like "Stored".
If the keyer runs out of memory during recording, if signals "F" (like "Full")
and stops recording automatically.
This QRP-Keyer also measures the gaps between WORDS (unlike NorCals famous
keyer by N6KR). The "Pause-code" together with the length of the pauis
recordas an individual character in memory and therefore occupies one
memory location. The Pause-Length is recded as a "multiple" a dot-length,
so if you replay a message with a higher speed than when recorng it, als¦j`Üä¤àÜä¤@@@{ðo
"long" pauses will become shorter.

Partitioning of o
"long" pauses will become shorter.

Partitioning of a Message
-------------------------
Instead of one "long" message you may also record multiple "shorter" messages
in a single message memory. I call this a "partitioned" message.
To separate all sub-messages in a memory you have to insert a special
character called "End Of Mage" (EOM). All Messages are recordeds one
"long" Message, with an EOM character at the end of each sub-message.
The EOM character is entered into the memory by running together the letters
E+O+M (".-----").

Playing a part of a "partitioned" Message
-----------------------------------------
To recall (play) the second part of a recorded message you have to press the
"Message"-Button as two times (with ony a short delay between to button-
"clicks").
To play the 3rd sub-message just press the button three times and so on.
If you press a message button quickly more often than there are sub-messages,
the keyer does not replay anything at all.
When playing a recorded message, the keyer will stop when it reaches an EOM
character in the message memory... for one exception: In the "memory-LIST-
mode" all codes that are stored in a memory are played "without conversion".
The "memory-list-mode" you will also hear the recorded EOM characters. More on
the "list mode" will follow below.


Side- and Signal-tone
---------------------
You may connect a small (passive) piezo speaker to pin 2 of the processor
(this pin is called "RA3" or "TONE" in the circuit diagram).
The piezo speaker will be able to generate a SIDE-TONE for CW transmission and
a SIGNAL-TONE to indicate special conditions (or "feedback") that may be
important for some operators.
During "normal" telegraph operation the sidetone may be useful if you want to
build the keyer into your homemade QRP transceiver.
In "command mode", for "Warnings" and other "Signals" the keyer sometimes
generates the lower-piched SIGNAL TONE.
It simplifies the operation of the keyer, especially if you often use the
"special functions" of the keyer.
Usually the signal tone will produce single morse codes at a FIXED speed (not
depending on the speed poti, about 60..80 letters per minute).
If you want to use the sidetone in, you may find a suitable piezo speaker in
an old electronic "happy birthday"-card.
If you don't want to use a piezo, because you have a transceiver with built-in
sidetone, you may use "optical" signals from a signal-LED. Connect a red
low-current LED from Pin 8 ("RB2" or "Signal LED") via resistor to ground.
This LED will only be driven by the keyer, when a SIGNAL TONE is generated.
Therefore the LED will **NOT** be on during "normal" CW transmission.

Command Mode
------------
Special commands to the keyer are entered in "command mode" with the paddles.
To enter command-mode, press both buttons simultaneously. The keyer will
answer with the signal-tone "C" (like "Command mode").
As long as the command-mode is active, the keyer tries to interpret all
characters that you enter with your paddles as "command". Usually a command
consists of a single morse letter. The keyer answers to every recognized
command with the signal-tone "R" ("Roger"), every command that could not be
recognized will be answered with the signal-tone "?" (question mark).
You may exit from command mode either by a second simultaneous touch of both
message-buttons or by entering the "D"-command ("Done") with the paddle(s).
The following command are implemented at the current time
 (there may be more, if I failed to update this manual):

Command "A": Turn DOT/DASH-memory OFF.
 With the DOT/DASH-memory turned off the keyer behaves like this: If you
 release the padddles while a dot or dash is being sent, the dot or dash
 will be completed, and nothing else is sent.
 In other words: If you touch the DOT, while a dash is being sent, and
 release the DOT before the transmission of the dash is over, there will
 *NO* dot be sent after the dash (in contrast to mode "B").
 I guess this is sometimes called "Iambic Mode A".

Command "B": Turn DOT/DASH-memory ON ("BETTER" Mode)
 This is my "preferred" keying mode, where the keyer stores the
 "opposite" element during transmitting of one element. For example, if
 you first touch the DASH and -while the dash is being sent(!)- touch the
 DOT, the keyer will send the DOT after the DASH is finished (no matter
 if you release the DOT before the end of the DASH-transmission).
 I guess this mode is called "Iambic B".

Command "D": "Done"
 Exits from "Command"-mode and returns to "normal" keyer operation.

Command "E": "Endless playing"
 Switches the memory-replay-modus to "endless loop".
 This allows playing a stored message (almost) endless, while the
 operator sits in the background drinking a cold beer. After 255 repeats
 the keyer terminates the "endless" replay loop (which prevents real
 "endless" transmissions, if the operator has to go "somewhere" and
 forgets to terminate transmission).
 Switching to "endless loop mode" does not start playing a message, you
 still have to start playing by pressing the message button.
 To terminate the "endless loop mode", enter a second "E" command.
 To terminate playing a message ("endless" or "normal") just touch the
 paddle.
  Tip: Append a long "pause" at the end of your cq-call-message, before
       you stop recording the cq-call.
       This will give you a delay for "listening".
       If you hear someone answering, touch the paddle and the "cq"-loop will
       stop.

Command "L": "List-mode"
 Can be used to check the content of a complete message buffer with
 "special functions".
 If you play a recorded message in "list mode", there will be no
 "conversion" of special codes like EOM, NNN and ANN.
 Return from "list mode" to "normal operation" with the "M"-command.

Command "M": "Macro-mode"
 If this message-replay-mode is active, special characters like "EOM",
 "NNN", "ANN" are treated in a special way.
 The characters "NNN" is "expanded" into three digits.
 This mode is the default mode, it is "complementary" to the "List-mode"
 (see "L"-command).

Command "N": "set Nummer for contest-operation"
 See chapter "Contest Operation". This command is used to initialize the
 "serial contest-number" to any value between 000 and 999.
 The keyer answers with the Signal-Tone "NR" to tell you that it expects
 the entry of a three-digit-number with the paddle(s).
 After the "N"-command you have to enter three digits, after entry of the
 last digit the keyer signals "R".

Command "Q": "Quick digits"
 Switches the digit-output-mode to "quick digit mode".
 In this mode the keyer will generate digits as follows:
   Digit:    0 1 2 3 4 5 6 7 8 9
   Output:   T A U V 4 5 6 7 8 N
 Note: The "quick digit modes" does not apply to normal recorded numbers.
    At the time of this writing this only applies to the expansion of the
    macro "NNN".
    You may always ENTER numbers using "normal" digits or "quick" digits, no
    matter if the quick digit mode is active or not. The keyer always
    "understands" both formats if it waits for a numeric input.

Command "S": "Standard digits" or "Slow digits"
 Switches the digit-output-mode back to the "standard"-mode.
 In this mode all digits "generated" by the keyer are given as morse-
 codes with 5 elements.

Command "T": "Tune"
 Turns the transmitter continuously ON (strictly speaking: for a maximum
 time of about 30 seconds).
 To stop "tuning" just touch a paddle or any message-button.
 If you stop "tuning" manually, the keyer will also exit from command
 mode.
 If the keyer stops "tuning" after the 30-second-timeout, it will **NOT**
 exit from command mode. You may then start a new 30-second-tune-interval
 with another "T".

Contest-Operation
-----------------
In combination with the two message-memories you may use the keyer as a real
"contest keyer" with automatic contest number generation. All you need is a
little "smart programming" of both message memories in combination with two
"macros" that you have to record along with your contest messages.
All you have to do during the contest is repeat the other station's callsign
and recall the proper message from the memory...
(If you don't like contests, you may use this "counter feature" for something
else or ignore this chapter)
These "macros" are used to generate numbers and to increment a counter:

Macro "NNN": ("Number Number Number")
  Is entered into a memory as "-.-.-." .
  Function:
    When playing a message, this macro will be "expanded" into a 3-digit
    contest number.
    This function can be called as often as wanted, it does **NOT** affect
    the contest counter !

Macro "ANN": ("Advance Number")
  Is entered into a memory as ".--.-." .
  Another way to remember this macro is:
   ".--.-." = "PN" = "Plus Number" or
   ".--.-." = "AC" = "Add Counter"
  Function:
    Incremets the "current contest-number" by one.
    It does **NOT** generate a "transmitted" character when played from a
    message memory.
    You will only "see" this macro in a message memory when you activate the
    "list-mode" ("L" command, see chapter "command mode").

As you can see, the macros "NNN" and "ANN" have to be combined in a contest.
The message that you use to give a contest report, will use the "NNN" macro
(maybe repeatedly). An example for a very simple contest report:
   "599/<NNN> 599/<NNN> BK <EOM>"
When playing this message, the keyer replaces the <NNN> by the current contest
number. It will transmit for example:
   599/123 599/123 BK
After a contest-"QSO" is complete, you will play a different message from
another message-memory (or at least from another partition of a message-
memory) which contains the macro "ANN".
It's ok to use a short message like this:
   "73 gl <ANN> qrz ?"
When playing this message the keyer only transmits this:
   73 GL QRZ ?
because the macro <ANN> only increments the contest number but it does not
"transmit" a character.
Next time you play the contest report from the first example, the keyer will
transmit
   "599/124 599/124 BK".


Technical Data
--------------
 Processor: PIC16F84-04/p
  - data sheet and development system available at WWW.MICROCHIP.COM
  - in the keyer driven with internal RC-Oscillator,
    clock frequency about 50kHz (!)
  - 1024 * 14 Bit EEPROM programm memory, serial programmable with a
    simple programming tool connected to your PC.
  - 68 Byte of internal RAM
  - 64 Byte of internal EEPROM
  - one 5-Bit-Port (Port A) and one 8-Bit-Port (Port B), Port B has
    switchable internal pull-up resistors
  - power-saving sleep-modes with "wake-up" on change of any input signal
    on Port B
  - 8-Bit Timer/Counter (not used in the keyer!)
 Power consumption (supply voltage = 2.4 V):
  - operational, no sidetone active: 60 microamperes
  - operational, with piezo-sidetone beeping: 200 microamperes
  - during standby: less than 1 microampere (typical)
  The keyer enters standby-mode automatically after some seconds of "no
  activity".


Software
--------
Use the file "KEYER1.HEX" that you may find on your local packet radio BBS
under "QRP".
Otherwise in the internet: www.qsl.net/dl4yhf/keyer1
Commercial use requires the author's permission.
The source code is available only on request. All rights reserved.


Circuit diagram and PCB
-----------------------
Circuit diagram and a "sample" PCB layout are available as  graphic files
on the author's homepage.
See "Software".


Kits ? Not yet..
----------------
but "Kit-Assemblers" who want to spread this keyer as a kit are welcome, as
long as they will offer kits for "ham spirit"-prices.


Exclusion of warranty
---------------------
Sorry, I hate this legal stuff, but here it comes:

 The author provides absolutely no warranty, to the extent permitted by
 applicable state law.
 The author and/or other parties provide this hard/software "AS IS"
 without warranty of any kind, either expressed or implied, including,
 but not limited to, the implied warranties of merchantability and
 fitness for a particular purpose.
 The entire risk as to the quality and performance of the hard/software
 is with you.
 In no event unless required by applicable law will the author and/or any
 other party who may modify and/or redistribute this hard/software be
 liable to you for damages, including any lost profits, lost monies, or
 other special, incidental or consequential damages arising out of the
 use or inability to use this package, or for any claim by any other
 party.



Read previous mail | Read next mail


 16.11.2026 22:20:53lGo back Go up