OpenBCM V1.13 (Linux)

Packet Radio Mailbox

DB0FHN

[JN59NK Nuernberg]

 Login: GUEST





  
DK8KV  > QRP      27.04.99 09:35l 525 Lines 24870 Bytes #-10065 (0) @ DL
BID : 274902DB0MKA
Read: DG6MS GUEST
Subj: Elecraft K2 TRX
Path: DB0ZKA<DB0CRL<DB0TTM<DB0FP<DB0SRS<DB0ZDF<DB0AIS<DB0NDK<DB0XO<DB0MKA
Sent: 990427/0759z @:DB0MKA.#NRW.DEU.EU [HennefJO30PR DL3OE] $:274902DB0MKA
de DK8KV @ DB0MKA.#NRW.DEU.EU   (Walter)

to QRP @ DL

Weil Mitte Mai/Juni die reagulaere Auslieferung des K2 QRP-Transceiver
Bausatzes erfolgt, hier eine Zusammenfassung der Herstellerangaben:


EleCraft K2 160-10M CW/SSB Transceiver
--------------------------------------
Product Description (4/23/99)
-----------------------------
 

Easy to Build:

     'No-wires' construction: most controls and connectors mount
     directly to PC boards. 
     Comprehensive user manual with step by step instructions and
     theory of operations. 
     Incremental assembly and test. 
     Modular, upgradeable. 
     No surface mount devices. 
     No specialized test equipment beyond a standard digital
     multi-meter is required for test and alignment. (Built in
     test.) The K2 even includes a built in general purpose
     frequency counter, volt meter and radio current drain meter. 
     Largest possible PC board pads and traces to simplify rework
     and repair. 
     Full documentation provided for user modifications. 

K2 High Performance CW Base Unit, General Features:

     Small, portable size. 2.9h x 7.8w x 8.2d inches. 
     Efficient 10-15 volt operation for home or field use. 
     Less than 110ma typical receive current (backlight off, low Ip
     mode, pre-amp off, headphones). 
     @200 ma typical receive current (high performance Ip mode) 
     Adjustable 0-10W PEP (via front panel menu). 
     Rugged, attractive custom enclosure. 
     Back-lit LCD display (backlight can be disabled). 
     160-10 meter ham band coverage, with some out of band
     overlap. (160 meters with 160m/RX Antenna option.) 
     PLL synthesized for low noise (no DDS spurs). 
     CW-only and SSB/CW (with SSB option). 
     Microprocessor controlled. 
     2 VFOs with split operation plus 10 memories. 
     Direct keypad entry of frequencies, memory channels and key
     parameters. 
     RIT and XIT. 
     Built-in speaker. 
     Headphone jack handles mono and stereo plugs 
     10 memories store Mode, VFO A/B, Split, RX filter, RX
     sideband (CW), etc. 
     Simple menu system for advanced settings. (Up to 2 menu
     functions can be assigned to the programmable front panel
     function keys.) 
     BNC antenna connector -- A QRP standard. (SO-239 on
     High Power option.) 
     Room for additional connectors on the rear panel for user
     modifications. 
     All options may be added at any time. 

Receiver:

     Double-balanced diode mixer for excellent front end dynamic
     range and IP3. 
     Ham Band bandpass RX/TX filtering, relay switched (for
     excellent IP2 on RX). 

 Preliminary K2 Performance Measurements (14MHz Typical Values)

  MDS(dbm)    IMDDR3(db) Ip3(dbm)   Ip2(dbm)   BDR(db)
  ------------------------------------------------------ 
  -136/-131   96/97      +2/+14     +77/+78    125/133 


     XX/YY = preamp-on/preamp-off results; 
             See K2 Performance Comparisons for more details.

     RX pre-amp and attenuator. (Both switchable on/off.) 
     Single conversion RX to 4.915 Mhz IF. 
     Room for up to three switchable IF crystal filters. 
     Smooth, Fast attack, IF-derived AGC (no 'popping' on strong
     signals) with fast/slow decay. (AGC can also be turned off). 
     IF gain adjust. 
     Sharp IF crystal filtering helps prevents receiver overload from
     signals outside the RX passband. (Much better adjacent
     signal rejection (without AGC pumping) than the
     switched capacitor audio only filtering of other rigs.) 
     1 Khz per knob revolution for fine tuning; also 10 and 100
     Khz per revolution. 
     10 Hz display resolution (7 digit). 
     Bar-graph S/RF OUT/ALC meter. 

CW Features:

     Full break-in CW. 
     Built in keyer with 10 programmable memories and both
     popular iambic modes A and B. 
     Sharp, variable bandwidth CW crystal filter (250 - 1750 Hz). 
     Options for a fixed-bandwidth narrow crystal filter or a
     wide-bandwidth crystal filter for tuning the band. 
     Adjustable RX CW pitch with tracking TX side tone. 
     Selectable opposite sideband RX for QRM reduction. 
     Normal / Reverse paddle setting for Dot / Dash; Manual Key
     setting. 
     Efficient transmitter operation. 

 SSB Option:

      8 pin microphone connector, jumper selectable compatibility
      with most Yaseu/Icom/Kenwood connectors. 
      Speech Compressor.  2.4 Khz (optional 2.7 Khz) crystal filter. 

 Noise Blanker Option: 

      High Performance noise blanker with variable threshold. 
      Buffered IF output to rear panel. 

 Auto-tuner Option: 

      10W Automatic Antenna Tuner. Latching Relays for extra low power drain. 
      Microprocessor goes into sleep mode after tuning for -no- RX birdies. 
      SWR and Power metering to front panel. Dual antenna selection (A/B) 

 High Power PA Option:

      50W (100W under consideration) internal PA module. 
      (Either the 10W Auto-Tuner and Battery Options or the High
      Power PA can be installed in the K2, but not both.
      The PA has its own K2 top cover which replaces the standard one.
      This way the PA can be swapped out with the Tuner / Battery options
      which mount to the regular K2 cover.)
      SO-239 RF Connector Amplifier Keying Output 

 Aux I/O Option:

      Host computer remote control via RS-232.
      (Most likely Kenwood command format.) 
      Aux Connector . (Includes Ext. Amp. keying) 
      Low Power transverter output (0 dbm.) 
      Real time clock. 

 160M / RX Antenna Option:

      Adds 160M TX/RX Switchable RX Antenna Input (all bands) 

 Other Options:

      SWR / Power and A/B antenna switch (no tuner). 
      Internal sealed battery (2.9AH). 
      AF active filter module. (Users may also design their own audio filter
      modules.) 
      Additional RX crystal filters.
      Blank crystal filter printed circuit boards for user
      designed RX filters. 

 Specifications and Pricing subject to change.
 EleCraft home page, www.elecraft.com  

K2 Circuit Description
----------------------
Wayne Burdick, N6KR and Eric Swartz, WA6HHQ

NOTE: We’re working on formatting the entire K2 owner’s
manual for the web, and we’ll post it as soon as it’s completed.
Additional details will be added as we convert each section. In
the mean time, the circuit details presented here should give the
reader a basic functional understanding of the K2. Some
familiarity with transceiver circuits is assumed in this version,
unlike the actual K2 manual, which is written at a more basic
level and includes a glossary of terms.

System Overview 

Packaging

The K2 transceiver is highly modular in design, allowing flexibility in
configuration and providing for future expansion. At the core of this
modular architecture are the three main circuit boards:

Front Panel

     User interface, including display and controls

Control Board 

     MCU, digital logic, DC control, AGC, and AF
     amplifier

RF Board 

     All RF circuitry, relays, and I/O processor (IOP)

This functional division allows related circuits to be grouped together,
but also provides a high degree of isolation between the analog and
digital sections of the transceiver. The RF board serves as a "mother
board" (see internal photos), while the front panel and control boards
plug into the RF board at its front edge. The front panel and control
boards are mounted back-to-back, with their ground-plane layers
forming a partial enclosure that helps minimize radiated digital noise.

The K2’s custom enclosure is also modular. It is fabricated in six
pieces, with a unique 2-D fastener used at each joint and for PCB
support. The modular design simplifies construction and alignment, as
well as providing a rugged but very light-weight enclosure that is ideal
for field or home use.

The top cover, which includes the upper portion of the rear panel,
can support a variety of built-in options such as an internal battery,
automatic antenna tuner, and host RS-232 interface. The top cover
can be replaced with a 100W power amplifier module, converting
the K2 into a medium-power station.

While we currently do not offer a remote front panel kit, this can
easily be accommodated in the future. The front panel and its PC
board can easily be unplugged from the front of the unit by removing
just four screws, and is sized for convenient mobile installation.

Block Diagram

The block diagram, Figure 1, shows overall signal flow in the K2.
Transmit and receive paths are shown for sideband operation. For
CW transmit, the BFO signal is routed directly to the transmit mixer,
not through the crystal filter(s).

The K2 receiver is a traditional single-conversion superhet, utilizing
double-tuned band-pass filters on each band and down-conversion
to a low I.F (4.915MHz). This approach results in excellent CW and
SSB performance: the low I.F. is compatible with narrow,
variable-bandwidth CW crystal filtering and allows the use of fast
I.F.-derived AGC. An I.F. of 4.915Mhz also results in nearly no
birdies across the entire tuning range.

The BFO is digitally controlled to allow upper and lower sideband
reception on any band, as well as CW on either sideband. AM
signals can be received in SSB modes thanks to the stable VFO,
although AM transmit is not currently supported.

Individual (per-band) band-pass filters offer improved 2nd order
IMD performance when compared to up-conversion designs that use
only a single low-pass filter to remove image products ahead of the
receiver. Up-conversion also requires the use of a second I.F. to
obtain good CW performance, increasing cost and producing
additional spurious signals. (An alternative is up-conversion followed
directly by a product detector and audio filter. While this results in
minimal parts count, it was not considered since the resulting CW
and AGC performance would have been poor.)

On transmit, signal flow is reversed; the BFO is combined with the
VCO to generate an output at the operating frequency, which is
filtered by the band-pass and low-pass filters. A highly stable power
amplifier chain provides 10 watts output or more on all bands, and
the output level can be set accurately in 0.2W increments. The
transmit strip is conservatively rated to provide excellent reliability
and immunity to high SWR; the same push-pull final amp design
could be pushed to over 40W on the lower bands. PIN-diode
switching is used to provide silent, no-relays QSK. (Please refer to
the RF Board section for further details.)

Coverage of 160-10 meters is provided by a single wide-range
VFO. High-side and low-side injection are both used, depending on
the band, so the overall VCO range is limited to about 6 to 24MHz.
Only one VCO is needed, with a single high-Q inductor and three
small DPDT relays configured to select one or more fixed capacitors.
The VCO is driven by a PLL synthesizer. 5kHz frequency steps are
used at the PLL, while 10Hz increments are provided by a 12-bit
DAC driving an 11MHz VCXO (PLL reference oscillator).

Microcontroller (MCU)

The K2’s microprocessor is an integral part of all transceiver
operations. Firmware is used to maximal advantage to provide many
functions traditionally provided by discrete control logic. For
example, the VCXO (PLL reference oscillator) is linearized on each
band by a firmware auto-calibration routine, with resulting tables
stored in EEPROM. Another example is firmware ALC, which is
used on CW to maintain the user-specified power level across all
bands. (The SSB adapter, when installed, provides its own optimized
hardware ALC.)

Extensive use of firmware also results in many useful operating
features not usually found on transceivers in this price class. These
features include built-in test equipment (frequency counter and digital
voltmeter), auto-calibration, dual VFOs, memories, split operation,
RIT/XIT, and a versatile keyer. Provisions have also been made in
firmware to support a wide range of option modules. (See full feature
list elsewhere on the web site.)

Latching Relays

Latching relays are used for all filter, VCO, and option switching, so
there is no relay current drawn during normal operation. This,
combined with careful power control at all stages in the transceiver,
results in receive-mode current drain as low as 100mA (using
headphones). The latching relays are all controlled by a single device,
the I/O processor (see below), which also handles other
miscellaneous I/O tasks on the RF board. DPDT relays are used for
all filter switching, reducing the number of relays needed by a factor
of two. 50-ohm switching is used for all filters, and this combined
with careful layout and guard-banding of the relays results in excellent
filter input/output isolation. 

Co-Processors and the AuxBus 

In keeping with the K2’s modular system architecture, much of the
I/O switching is handled by co-processors. There is only one
co-processor in the basic K2, the I/O Processor (IOP). Some
option modules, such as the SSB adapter, have their own
co-processors. This technique distributed processing allows
future modifications to be made to option boards without changing
the transceiver itself. It also reduces cost of the basic K2, since
fewer main-processor control lines are needed. 

The IOP, as well as all co-processors on option modules, go into
"sleep" mode with their own 4MHz clocks suspended during normal
operation. For this reason, there is virtually no digital noise on the RF
board to cause receiver EMI.

When the operator performs an operation that changes relay states,
the main processor (on the control board) wakes up the
co-processors and sends one of them a configuration command.
These commands are transmitted on a one-wire network, the
AuxBus. The AuxBus network line sits at a logic high during normal
operation, and is only activated when needed. The receiver is muted
during commands, so the operator never hears any digital noise.

Most AuxBus transmissions occur due to operator requests such as
a band change. However, the AuxBus may also be used during
transmit to relay numeric data such as SWR or ALC from a
coprocessor to the main processor. Waking up the coprocessors
during transmit has no effect on the transmitted signal.

Front Panel

Figure 2 shows the front panel schematic. The front panel PC board
plugs into the RF board via a 20-pin single-row connector, P1. is
made up of a number of user-interface elements:

     The LCD, DS1, is an 8-digit 7-segment transflective type with
     three backplanes (triplexed). Its driver, U1, receives display
     commands via an I2C interface. The LCD backlight LEDs, D2
     and D3, are used to provide enough brightness to handle
     low-lighting situations ("NITE" mode in the menu), while
     drawing only a small amount of current (<30mA). However,
     they can be turned off when ambient lighting is sufficient
     ("DAY" mode) because the LCD is transflective, i.e. it can
     either reflect or transmit light. The LCD displays the operating
     frequency and status messages, and also has 8 annunciators
     which indicate the settings of various controls. 
     A 10-segment LED bargraph, DS2, is used to display
     received and transmitted signal strength and ALC level. Using
     the menu, the operator can select DOT or BAR mode for the
     bargraph, with DOT mode typically used to save current
     during battery operation. U3 and U4 are 8-output MOSFET
     driver arrays which control the bargraph, among other things.
     Q1 and Q1 form a brightness control. When the NIGHT(low)
     control line is pulled to ground by U3, the bargraph supply
     voltage drops to 2.7V, resulting in about 6mA/LED. The LCD
     backlight is also turned ON in this case. When NIGHT(low) is
     left high for daytime use, each LED draws about 18mA, and
     the LCD backlight is OFF. 
     A high-quality optical shaft encoder, Z1, provides 100 counts
     per turn, allowing VFO tuning steps 10, 100, or 1000Hz per
     increment (1, 10 and 100kHz per turn, respectively). The
     encoder is also used to modify parameters in the menu. The
     encoder can be turned off by U3 to save current under certain
     operating conditions. 
     S1-S16 are pushbutton switches. Switch data is read by U2,
     an 8-bit parallel-to-serial shift register. Each switch has at least
     two functions: the top label corresponds to a TAP (short
     press) and the bottom label corresponds to a HOLD (long
     press, ~0.35s). Two-switch combinations are also supported,
     although only one is in use presently (BAND+ and BAND-
     together enter direct frequency entry mode). 
     Potentiometers R1, R2 and R5 (Keyer Speed, Power Out,
     and RIT/XIT Offset) are multiplexed onto a single A-to-D
     input of the MCU, the "VPOTS" line, so their position can be
     read. Firmware hysteresis is used for these controls to prevent
     noise from interfering with the readings. The AF Gain control
     is not read by the MCU; its leads go directly to the input of
     the AF amp on the Control Board. (The entire path from
     product detector to AF amp is balanced to prevent
     common-mode noise pickup—see Control Board for details.)
     As is true of most modern transceivers, the RF Gain control
     actually controls the receiver’s IF gain; it varies the DC
     control voltage on pin 5 of U12 (RF Board). 
     The circuitry associated with J2, the mic jack, is only present if
     the SSB option is installed. P1 is a configuration header that
     the user can wire as needed to support any of several
     industry-standard microphones with an 8-pin circular
     connector. Q3 and its associated resistors are used to
     multiplex the UP, DOWN, and FUNCTION lines from P1
     onto the VPOTS line to allow the mic to send commands to
     the MCU. The PTT line from the MIC activates the
     DOT-PTT(low) line to initiate transmit. The MICAF line, mic
     audio output, is amplified and processed by circuitry on the
     SSB adapter (see Option Modules). 

Control Board 

Figure 3 shows the control board schematic. The control board plugs
into the RF board via connectors P1, P2, and P3 (along the bottom
edge of the schematic). P1 handles AGC signals while P2 and P3
provide miscellaneous I/O. Redundant connections are provided for
ground, supply voltages, low-impedance signals (such as audio
output) and a few other critical signals.

U6 is a PIC16C77 microcontroller (MCU), with 8K of EPROM,
300+ bytes of RAM, serial I/O, parallel I/O, and A-to-D inputs. It is
self-contained with the exception of its 4MHz crystal oscillator, X2.
Even when running at 4MHz, the PIC processor is very efficient: it
only draws a few milliamps at 5V. Also, since the program and data
memories are located on-chip, there is very little noise radiation from
the MCU.

To get the most out of the available I/O on the MCU, much of the
communication from MCU to the rest of the K2 is done via serial
interfaces:

     RS232: Used for communicating with a host computer via P4
     (Aux I/O) 
     I2C: Display driver data 
     SPI: The serial peripheral interface is used to access various
     peripherals, including the PLL and DACs. 
     AuxBus: 1-wire data network for co-processor control 
     Shift register I/O: serial-to-parallel shift registers are used to
     access MOSFET LED drivers on the front panel; a
     parallel-to-serial shift register on the front panel is used for
     reading pushbuttons. 

Note: A future version of this manual section will include details on
K2 firmware implementation. See Operation for information on
firmware features, menus, etc.

In addition to the microcontroller the control board provides a
number of specialized hardware interfaces. Moving from left to right,
top to bottom on the schematic:

     ALC: U10A and associated circuitry are used to accurately
     control power output as well as provide CW waveform
     shaping. 
     Frequency counter: Q9 and Q10 form a two-stage amplifier,
     supplying a square wave signal to the MCU when the
     frequency counter is enabled and a probe is connected to P6.
     The counter amp is turned off at all times except when one of
     the calibration routines is being used. 
     Quad DAC: The four outputs from this DAC provide: audio
     tones (via U10B), BFO frequency control (U10D), and
     crystal filter bandwidth control (U10C). Audio tone pitch,
     amplitude, and wave shape are controlled in firmware to yield
     very clean sidetone as well as general-purpose tones from 300
     to 1000Hz. The bandwidth control line doubles as the
     transmitter driver bias control on transmit, allowing the driver
     bias to be set to a lower level when running at lower power
     output. 
     EEPROM: U7 provides 2K bytes of non-volatile
     configuration data storage. This memory is used for VCO
     lookup tables, CW messages, frequency memories and other
     variables that must be permanently saved. The EEPROM can
     be written millions of times without loss of data. During normal
     operation on a single frequency (such as when in a QSO), the
     EEPROM is not accessed at all. However, whenever the
     VFO is moved, a 30-second timer is triggered. Once the
     VFO has stopped moving for 30 seconds, the EEPROM is
     updated with the latest VFO frequency. In this way, the K2
     always saves the most recent "important" frequency. (The
     EEPROM update also takes place any time you change bands
     or operating modes, etc., so you don’t have to wait for 30
     seconds to record an important configuration change.) An
     alternative strategy used by many rigs is to use
     battery-backed-up RAM, continuously recording the
     operating frequency. However, we preferred to eliminate the
     backup battery, which often has a high failure rate and must be
     periodically replaced. 
     Voltmeter and ammeter: Using S1, the operator can monitor
     either the internal 12V supply voltage or, during alignment, the
     voltage from a test probe plugged into P5. U3B buffers the
     DC signal from the probe, and also is used in conjunction with
     Q11 to provide supply current monitoring. The current sense
     resistor, which has a value of 50 milliohms, is located on the
     RF board (R115). 
     Voltage regulators: U4 is a low-dropout 8V regulator, which
     is stable with a K2 input DC voltage as low as 8.2V. Since all
     signal-generating and signal monitoring stages in the K2 run
     from this 8V supply, the transceiver will function normally even
     when running from very depleted batteries; most transceivers
     use a higher regulated voltage for these stages and in some
     cases will not operate reliably even at a battery voltage of
     11V. (Transmit power will be scaled back and a warning
     message displayed if the battery voltage drops below a critical
     value or if current drain is excessive.) U5 provides 5V for
     logic circuits on the front panel and control board, but this
     signal does not appear on the RF board, so noise is minimized. 
     8V Switching: Q1 and Q2 provide stable +8V sources on
     transmit (8T) and receive (8R). Q5 is needed to guarantee
     that 8R goes to 0V on receive to maintain proper reverse
     voltage on T-R switch diodes. 
     Audio Filter: This is a small module mounted on the back of
     the control board which will supply analog and/or digital audio
     filter functions. The audio filter module has its own
     co-processor so that it can be enhanced in the future. 
     Mute: Q6 and Q7 disconnect the AF amplifier from the
     product detector on transmit, which is necessary for clean QSK. 
     AF Amp: U9 is an LM380 audio amp IC, supplying
     approximately 1W of audio drive to a 4-ohm speaker in the
     cover of the K2. Sidetone is injected post-volume control. 
     AGC: Mixer/oscillator U1 generates a low-level signal at
     about 5.068MHz, then mixes it with the 4.915Mhz I.F. signal
     from the RF board to produce a new auxiliary I.F. of about
     150kHz. This auxiliary I.F. signal is then amplified by U2B
     and detected by D1 to create a positive-going AGC voltage,
     which is then routed back to the RF board to control the I.F.
     amp (U12). While it is possible to generate the same AGC
     voltage by simply amplifying and detecting the 4.915Mhz
     signal itself, this technique often necessitates shielding of the
     AGC RF amplifier stages to prevent radiation of the I.F. or
     BFO signals back into the receiver I.F. strip. We obtain all of
     the gain at 150kHz instead, so the 4.915MHz signal is not
     re-radiated. 150kHz is high enough to obtain fast AGC
     response two orders of magnitude faster than is possible
     when audio-derived AGC is employed. 





Read previous mail | Read next mail


 17.11.2026 04:12:07lGo back Go up