OpenBCM V1.13 (Linux)

Packet Radio Mailbox

DB0FHN

[JN59NK Nuernberg]

 Login: GUEST





  
DG0AN  > LINUX    27.05.99 12:38l 163 Lines 4020 Bytes #999 (999) @ DL
BID : R59DB0ZDF00M
Read: GUEST DL7NDR
Subj: linkt-0.6.0-Test
Path: DB0MAK<DB0BOX<DB0ABH<DB0SRS<DB0ZDF
Sent: 990527/0930z @:DB0ZDF.#RPL.DEU.EU [ZDF Mainz JN49CX OP:DF4WJ] BCM1.40j
From: DG0AN @ DB0ZDF.#RPL.DEU.EU  (Walter)
To:   LINUX @ DL
Reply-To: DG0AN @ DB0GV.#HES.DEU.EU
X-Info: No login password

Hallo allerseits, habe soeben linkt-0.6.0 heruntergeladen und
mit SuSE 6.1, Kernel 2.2.9 und den in SuSE "eingebauten"
ax25-utils und -devels zu installieren versucht.
Die Übersetzung bricht ab mit der Fehlermeldung, daß die Datei
"qchkbox" nicht vorhanden sei, was auch stimmt.
In diesem Falle ist in

                   ..../linkt-0.6.0/linkt/dialog.h

die Zeile 

                   #include <qchkbox.h>    zu ändern 
                   
in                 #include <qcheckbox.h> .

Dann geht's.
Hier mein Testequipment für den ersten Versuch:
SuSE 6.1 mit Kernel 2.2.9
"eingebaute ax25-utils"
"eingebaute ax25-devels"    ist sehr wichtig !
"eingebaute z8530-utils"
KDE-Paket installiert
Baycom - USCC-Karte mit nur einem 9k6-Kanal,
                    1k2-Kanal nicht aktiv
T7F
z8530-Unterstützung als Modul


Hier zur Information meine Dateien, überall wo "MYCALL" steht,
ist das eigene Call einzutragen (evtl. mit SSID)

Die Datei /etc/ax25/z8530drv.conf
# z8530drv.conf - initialization for the Z8530 SCC driver
#
# Lines must not be longer than 255 bytes!
#
#
# Hardware section
#
# SCC chip 1
#
chip	1
data_a  0x320			# data port A
ctrl_a  0x324			# control port A
data_b  0x321			# data port B
ctrl_b  0x325			# control port B
irq     7			# IRQ No. 5 (#)
pclock  4915200			# clock (+)
board   BAYCOM                  # hardware type (*)
escc    no			# enhanced SCC chip? (8580/85180/85280) (*)
vector  no			# latch for interrupt vector ($)
special no			# address of special function register (*)
option  0			# option to set via sfr (*)
#
# (*) option, default value is 0
# (+) option, default is 4915200
#
# (#) all chips can share one interrupt, or you may use multiple INTs,
#     but there must be at least one IRQ defined in this system.
# ($) only one Vector Latch for all Chips is allowed.
#
#
# Software section
#
# The order of entries IS important!
#
# 	first     : DEVICE
# 	then      : MODEM section
# 	after that: Level 1 parameters
#
# Definition of /dev/scc0
#
device	/dev/scc0
#
# MODEM related stuff
#
speed	9600			# 9600 baud
clock	ext			# clock source: use modem-clock
mode	nrz			# NRZ operation
#
# Level 1 parameters
#
txdelay 8
persist 64
slot	8
tail	2
fulldup	0
wait    2
min	3
maxkey	7
idle	3
maxdef  120
group   0
txoff   off
softdcd off
#
# End of File


die Datei /etc/ax25/axports

# /etc/ax25/axports
#
# The format of this file is:
#
# name  callsign        speed  paclen window    description
#                       to
#                       PC
#
baycom	MYCALL-12        1200	255	7	BayCom-Modem (1200 bps)
uscc	MYCALL-9 	19200	255	7	USCC-Karte   (9600 bps)



Das Startscript /uscc

#!/bin/sh
# 
#
insmod scc 
sccinit
sccparam scc0 txdelay 15
# !!! Parameters for DAMA only !!!
sccparam scc0 persist 255
sccparam scc0 waittime 1
sccparam scc0 slottime 1
# !!! Parameters for DAMA only !!! 
# assign a TCP/IP-addr. and a call---> man ifconfig
# customize your TCP/IP - addr.   and    your call
#                  -------------         --------
#                  vvvvvvvvvvvvv         vvvvvvvv
ifconfig scc0 inet 192.168.17.10 hw ax25 MYCALL-9 mtu 1024 up
# !!! They are only dummy TCP/IP -addrs. !!!!
# report the settings:
ifconfig
linkt
# End of Script
Daß das Script ausführbar gemacht werden muß ist wohl klar.


Jetzt sollte unter anderem etwa folgendes zu sehen sein:
.
.
.
scc0      Link encap:AMPR AX.25  HWaddr DG0AN-9  
          inet addr:192.168.17.10  Mask:255.255.255.0
          UP RUNNING  MTU:1024  Metric:1
          RX packets:631 errors:5688 dropped:0 overruns:0 frame:0
          TX packets:81 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:16 



Das alles läuft bei mir nicht unter KDE sondern im fvwm2

Dieser Text wurde wie oben beschrieben gesendet.                                    
                   
                                                                                               


Read previous mail | Read next mail


 20.11.2026 17:46:48lGo back Go up