| |
DJ1AA > KAM 25.02.02 19:02l 776 Lines 39807 Bytes #999 (0) @ EU
BID : K2CDB0EIN002
Read: DB1VQ GUEST
Subj: KAM..xx SUPPORT FORUM (DJ1AA)
Path: DB0AAB<DB0KFB<F8KOX<F6KNP<F6KVE<F6KFT<LX0PAC<DB0GE<DB0ZDF<DB0AIS<
DB0ROF<DB0ERF<DB0ABZ<DB0EAM<DB0SMG<DB0EIN
Sent: 020220/1657z @:DB0EIN.#NDS.DEU.EU [LINUX BCM Kreiensen/Harz] bcm1.42j $:K
From: DJ1AA @ DB0EIN.#NDS.DEU.EU (Mirko-AB0DL)
To: KAM @ EU
Hello Kantronics User,
I got a lot of questions and answers and I want to spread out
the informations in the packet net as well. If you want you can
get the infos on the internet. On the Kantronics page it is possible
to activate a kind of forum newsletter.
Have a nice day, greetings Mirko +++ DJ 1 AA / AB 0 DL +++
------------cut---------------cut---------------cut-------------cut-----------
*** Message forwarding to: dj1aa@darc.de
*** MID: 10527_VE7TSI Size: 1331 bytes
Area: 'dj1aa' Current msg# 64 of 88.
?,A,APRS,B,BBS,C,D,DX,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,W,X,Y>
Message #64
Date: Sun, 10 Feb 2002 04:23:21 -0600
Message-Id: 6959VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: kenbaker@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] Re: KPC-3+ and Garmin eTrex
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#603) Re: KPC-3+ and Garmin eTrex
<http://www.kantronics.com/forum/index.cgi?review=603>
AUTHOR: Chris Edstrom <cedstrom@stanford.edu>
DATE: Sunday, 10 February 2002, at 4:23 a.m.
Reply To: (#526) KPC-3+ and Garmin eTrex
Author: Chris Edstrom,
Date: Tuesday, 1 January 2002, at 4:25 p.m.
Well, I have figured my problem out and am replying to my own message for the
sake of posterity :).
So, it turns out that I had a little wiring problem. I had bought the REAL
Garmin serial cable, not the one that doesn't have a connector on it, since
the "OEM" one was not available at the store where I got the cable. Well,
anyway, tricky as they are, in the "REAL" serial cable, (the one that actually
has a nine pin on it) the output line is greenish-yellow, and the input line
is white; HOWEVER, on the "OEM" cable, (without connector) the colors are
reversed. Since I read the schematic from the web, of course, it assumed that
I was using the OEM cable, hence, mixing up the colors. Well, I hope this
helps someone out there!
--Chris
P.S. Yay for standards! We love them so much, in fact, that we have multiple.
:)
> Hello all,
> I've just gotten a FT-1500M and a KPC-3+ to do some APRS tracking.
> I'm able to get the KPC-3+ to receive data from a PC and off the air, as
> well as program an LT to transmit data. However, I cannot get it to
> transmit data from the GPS using GPSHEAD.
> I've been able to determine that the GPS (Garmin eTrex) is sending out
> positional data at the right rate -- it interfaces correctly to a PC.
> However, I'm having a heck of a time interfacing the GPS with the KPC-3+.
> Currently, I've got the GPS to KPC-3+ cable with data on the XCD pin and
> ground on the 9 pin on the back of the TNC (radio port) which I believe to
> be the correct setup. Also, I have set CD to SOFTWARE as to not interfere
> with the GPSPORT command.
> I am using the GPSPORT command to try to gather data. Does the TNC need to
> be in INTFACE GPS to receive data from the XCD pin that is activated by
> GPSPORT? I believe that it does not.
> Well, any insight or comments would be much appreciated as I am basically
> tearing my hair out at this point :)
> Any help is MUCH appreciated. Cheers!
> - Chris (KG6FLT)
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
kenbaker@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #65
Date: Sun, 10 Feb 2002 13:09:34 -0600
Message-Id: 7817VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: kenbaker@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] KA-Node and X1J4 compatibility
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#604) KA-Node and X1J4 compatibility
<http://www.kantronics.com/forum/index.cgi?review=604>
AUTHOR: Jerry Curry <jercurry@att.net>
DATE: Sunday, 10 February 2002, at 1:09 p.m.
Does anyone know if the KA-Node will work in a system using X1J4 Nodes and how
compatible it will be? Need to 'replace' a X1J4 node and have KA available but
hear the KA- is not fully compatible and may not handshake etc properly.
I haven't found a lot of info that points out the problems...if there are any.
Any info would be great.
73 Jerry
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
kenbaker@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #66
Date: Sun, 10 Feb 2002 15:44:13 -0600
Message-Id: 36110VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: kenbaker@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] Re: KA-Node and X1J4 compatibility
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#605) Re: KA-Node and X1J4 compatibility
<http://www.kantronics.com/forum/index.cgi?review=605>
AUTHOR: Sean Smithers <seans@cdsnet.net>
DATE: Sunday, 10 February 2002, at 3:44 p.m.
Reply To: (#604) KA-Node and X1J4 compatibility
Author: Jerry Curry
Date: Sunday, 10 February 2002, at 1:09 p.m.
Hello Jerry
Do yourelf a favor and get the KNET node chip and install it in your
Kantronics TNC. Different ones are available from Kantronics for the KPC-3,
KPC-3 Plus and KPC-9612. Converts your KPC product to a full routable node
that can replace the X1J4 node.
The KA-Node does not propagate itself into the Nodes Tables, does no nodes
broadcasts and is essentially half a node. You will have a break in the nodes
chain that means your network users will have to know the KA-Node Call in
order to connect through it as all the other NETROM, THENET and X1J4 nodes
will not be able to include it in their routing tables.
Sean
> Does anyone know if the KA-Node will work in a system using X1J4 Nodes and
> how compatible it will be? Need to 'replace' a X1J4 node and have KA
> available but hear the KA- is not fully compatible and may not handshake
> etc properly.
> I haven't found a lot of info that points out the problems...if there are
> any.
> Any info would be great.
> 73 Jerry
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
kenbaker@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #67
Date: Mon, 11 Feb 2002 19:35:41 -0600
Message-Id: 35901VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: kenbaker@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] KAM Manual
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#606) KAM Manual
<http://www.kantronics.com/forum/index.cgi?review=606>
AUTHOR: Rick Altherr <kc8apf@kc8apf.net>
DATE: Monday, 11 February 2002, at 7:34 p.m.
I am looking for a KAM manual. A copy would be fine. Fax, email, pdf,
anything.
Rick
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
kenbaker@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #68
Date: Mon, 11 Feb 2002 19:43:38 -0600
Message-Id: 39462VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: kenbaker@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] KAM Manual
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#606) KAM Manual
<http://www.kantronics.com/forum/index.cgi?review=606>
AUTHOR: Rick Altherr <kc8apf@kc8apf.net>
DATE: Monday, 11 February 2002, at 7:34 p.m.
I am looking for a KAM manual. A copy would be fine. Fax, email, pdf,
anything.
Rick
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
kenbaker@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #69
Date: Mon, 11 Feb 2002 19:40:18 -0600
Message-Id: 1478VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: kenbaker@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] KAM Manual
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#606) KAM Manual
<http://www.kantronics.com/forum/index.cgi?review=606>
AUTHOR: Rick Altherr <kc8apf@kc8apf.net>
DATE: Monday, 11 February 2002, at 7:34 p.m.
I am looking for a KAM manual. A copy would be fine. Fax, email, pdf,
anything.
Rick
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
kenbaker@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #70
Date: Mon, 11 Feb 2002 19:44:18 -0600
Message-Id: 37293VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: kenbaker@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] KAM Manual
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#606) KAM Manual
<http://www.kantronics.com/forum/index.cgi?review=606>
AUTHOR: Rick Altherr <kc8apf@kc8apf.net>
DATE: Monday, 11 February 2002, at 7:34 p.m.
I am looking for a KAM manual. A copy would be fine. Fax, email, pdf,
anything.
Rick
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
kenbaker@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #71
Date: Mon, 11 Feb 2002 19:51:16 -0600
Message-Id: 13633VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: kenbaker@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] Re: KAM Manual
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#607) Re: KAM Manual
<http://www.kantronics.com/forum/index.cgi?review=607>
AUTHOR: Jack <wd8brj@yahoo.com>
DATE: Monday, 11 February 2002, at 7:51 p.m.
Reply To: (#606) KAM Manual
Author: Rick Altherr
Date: Monday, 11 February 2002, at 7:34 p.m.
I have all three. All modes of getting it there are open. eMail me and
let me know. Im over here on the other side of the state.
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
kenbaker@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #72
Date: Mon, 11 Feb 2002 22:50:24 -0600
Message-Id: 21297VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: elmer@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] test 7 (ignore)
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#610) test 7 (ignore)
<http://www.kantronics.com/forum/index.cgi?review=610>
AUTHOR: webmaster <larry@larryville.com>
DATE: Monday, 11 February 2002, at 10:50 p.m.
fklds nfkos jnfkdosnkds fpbwnjqa
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
elmer@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #73
Date: Mon, 11 Feb 2002 22:58:32 -0600
Message-Id: 24909VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: elmer@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] test 8 (ignore)
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#611) test 8 (ignore)
<http://www.kantronics.com/forum/index.cgi?review=611>
AUTHOR: webmaster <kaweagle@yahoo.com>
DATE: Monday, 11 February 2002, at 10:58 p.m.
jfkod fjdksopfjnewko fnksdalpnf
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
elmer@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #74
Date: Mon, 11 Feb 2002 23:04:43 -0600
Message-Id: 8818VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: elmer@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] test 9 (ignore)
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#612) test 9 (ignore)
<http://www.kantronics.com/forum/index.cgi?review=612>
AUTHOR: webmaster <kaweagle@yahoo.com>
DATE: Monday, 11 February 2002, at 11:04 p.m.
jfkdsop fnjdska fndsklfn[lsa
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
elmer@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #75
Date: Mon, 11 Feb 2002 23:10:53 -0600
Message-Id: 39980VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: kenbaker@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] test 10 (ignore)
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#613) test 10 (ignore)
<http://www.kantronics.com/forum/index.cgi?review=613>
AUTHOR: webmaster <kaweagle@yahoo.com>
DATE: Monday, 11 February 2002, at 11:10 p.m.
jkfonka fndkoapjdks ofnkdsa fnkospa
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
kenbaker@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #76
Date: Wed, 13 Feb 2002 22:30:02 -0600
Message-Id: 1556VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: service@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] KAM+ CALLSIGN
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#614) KAM+ CALLSIGN
<http://www.kantronics.com/forum/index.cgi?review=614>
AUTHOR: John Magnuson <n0eg@socket.net>
DATE: Wednesday, 13 February 2002, at 10:30 p.m.
My KAM+ does not prompt me to "PRESS (*) TO SET BAUD RATE" which it is
supposed
to do on startup. Neither am I prompted to "ENTER YOUR CALLSIGN".
MYCALL works, so there is communication between the computer and radio, but
CONNECT xxxxx-1 does not work. The xmit led flashes
for a minute or so, then it disconnects. I am just trying to get into
the mailbox; I don't have a radio connected yet. How can I get into the
CALLSIGN routine?
New with digital modes,
John N0EG
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
service@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #77
Date: Fri, 15 Feb 2002 02:47:07 -0600
Message-Id: 8981VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: service@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] Re: Interfacing The Interface to C-128
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#615) Re: Interfacing The Interface to C-128
<http://www.kantronics.com/forum/index.cgi?review=615>
AUTHOR: Lucio <lucioa@camserv.unicam.it>
DATE: Friday, 15 February 2002, at 2:43 a.m.
Reply To: (#502) Interfacing The Interface to C-128
Author: Raymond Sirois
Date: Wednesday, 19 December 2001, at 8:31 a.m.
Hello Ray, wath interface you ar in use for your tries? i have used C128 for
many years with Kantronics KPC4 & KAM.
The first is in this case to Know that your C128 have a
"user communications port"
working at TTL Level and non RS232 so, change the switch jumper mode
"RS232 to TTL" inside the TNC or it is necessary a level convertor to match
it.
The second questions is to establish the link from a terminal program on your
C128 and ....interface......... configured the link in terms of baud (ABAUD)
2400 baud is good for C128 and the handshaking line , details in the manual
installations of the products , you may have the operating conditions in the
severals mode as you want.
Excuse me if my info's is already know from you,
hope helpfull for you something of my answer,
73 from I6AAD
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
service@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #78
Date: Fri, 15 Feb 2002 09:38:53 -0600
Message-Id: 8039VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: service@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] rprint command ?
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#616) rprint command ?
<http://www.kantronics.com/forum/index.cgi?review=616>
AUTHOR: beau <n9mfk@aarl.net>
DATE: Friday, 15 February 2002, at 9:38 a.m.
hello i have a kpc-3
i was reading how rprint throught the remote could control a rs2332 device
but i can not get it to work tnx for any info
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
service@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #79
Date: Sun, 17 Feb 2002 09:39:47 -0600
Message-Id: 40568VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: service@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] Re: KPC-3 Question
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#617) Re: KPC-3 Question
<http://www.kantronics.com/forum/index.cgi?review=617>
AUTHOR: PAUL FLAUTT <pflautt@netpluscom.com>
DATE: Sunday, 17 February 2002, at 9:39 a.m.
Reply To: (#600) KPC-3 Question
Author: paul flautt
Date: Thursday, 7 February 2002, at 2:35 p.m.
> I did some more checking out on this unit and found when the squelch is
opened up the unit's Rcv and Mail lamps come on.The lamps stay on at this
point
until I reset the power on the unit.Does anybody have any thoughts on what
will
clear this problem.Paul
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
service@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #80
Date: Sun, 17 Feb 2002 15:32:57 -0600
Message-Id: 24443VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: service@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] KAM XL Flash a Big Problem... HELP!
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#618) KAM XL Flash a Big Problem... HELP!
<http://www.kantronics.com/forum/index.cgi?review=618>
AUTHOR: Jack Wilson wb7 <jwilson@nwsoftware.com>
DATE: Sunday, 17 February 2002, at 3:32 p.m.
Last evening I got my new KAM XL up and running. Checking the website I
noticed that there was an update available for the flash. I downloaded it,
followed the instructions and what happened? BIG MISTAKE! It does not work! I
cannot even get the old .hex file that is on the CD to reinstall. Both of them
tell me at 65536 that there is an error loading the file. Now my unit is down.
Has anyone been able to get the flash to load? If you did, how did you get it
to load without erroring out? Any assistance would be greatly appreceiated. I
don't want to begin feeling like I spent $400.00 for nothing!
Jack Wilson
WB7EOK
Everett, WA
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
service@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #81
Date: Mon, 18 Feb 2002 09:34:24 -0600
Message-Id: 57383VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: service@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] Re: KAM XL Flash a Big Problem... HELP!
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#619) Re: KAM XL Flash a Big Problem... HELP!
<http://www.kantronics.com/forum/index.cgi?review=619>
AUTHOR: LX1NO <lx1no@arrl.net>
DATE: Monday, 18 February 2002, at 9:34 a.m.
Reply To: (#618) KAM XL Flash a Big Problem... HELP!
Author: Jack Wilson wb7
Date: Sunday, 17 February 2002, at 3:32 p.m.
> Last evening I got my new KAM XL up and running. Checking the website I
> noticed that there was an update available for the flash. I downloaded it,
> followed the instructions and what happened? BIG MISTAKE! It does not
> work! I cannot even get the old .hex file that is on the CD to reinstall.
> Both of them tell me at 65536 that there is an error loading the file. Now
> my unit is down.
> Has anyone been able to get the flash to load? If you did, how did you get
> it to load without erroring out? Any assistance would be greatly
> appreceiated. I don't want to begin feeling like I spent $400.00 for
> nothing!
> Jack Wilson
> WB7EOK
> Everett, WA
Check this link
> See "Just downloaded 021 uploaded no problems"
> http://groups.yahoo.com/group/airmail2000/
It will help with the download problem you have.
73 Norby
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
service@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #82
Date: Mon, 18 Feb 2002 09:36:10 -0600
Message-Id: 22288VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: service@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] Re: KAM XL Flash a Big Problem... HELP!
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#620) Re: KAM XL Flash a Big Problem... HELP!
<http://www.kantronics.com/forum/index.cgi?review=620>
AUTHOR: Clay <aa3jy@arrl.net>
DATE: Monday, 18 February 2002, at 9:36 a.m.
Reply To: (#618) KAM XL Flash a Big Problem... HELP!
Author: Jack Wilson wb7
Date: Sunday, 17 February 2002, at 3:32 p.m.
> Last evening I got my new KAM XL up and running. Checking the website I
> noticed that there was an update available for the flash. I downloaded it,
> followed the instructions and what happened? BIG MISTAKE! It does not
> work! I cannot even get the old .hex file that is on the CD to reinstall.
> Both of them tell me at 65536 that there is an error loading the file. Now
> my unit is down.
> Has anyone been able to get the flash to load? If you did, how did you get
> it to load without erroring out? Any assistance would be greatly
> appreceiated. I don't want to begin feeling like I spent $400.00 for
> nothing!
> Jack Wilson
> WB7EOK
> Everett, WA
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
service@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #83
Date: Mon, 18 Feb 2002 13:08:22 -0600
Message-Id: 1049VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: service@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] Re: KAM XL Flash a Big Problem... HELP!
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#622) Re: KAM XL Flash a Big Problem... HELP!
<http://www.kantronics.com/forum/index.cgi?review=622>
AUTHOR: Clay <aa3jy@arrl.net>
DATE: Monday, 18 February 2002, at 1:08 p.m.
Reply To: (#621) Re: KAM XL Flash a Big Problem... HELP!
Author: Jack Wilson wb7
Date: Monday, 18 February 2002, at 10:39 a.m.
> After a further review of the list, I did try the upload using the
> Hyperterm program and only after I got of my /XP or /2000 windows boxes
> did it work. I orginally tried the script program that Kantronics provides
> and that is where I was having problems. (Hopefully, Kantronics will read
> these messages.) I tried the script with every version of Windows except
> /95. (I develop software for a living and have multiple computers with the
> various Windows versions for testing). The result was the same every time.
> The Hypertem solution only appears to work on Windows /98. There is
> something about the MS-DOS prompt in Win 2K and /XP the precludes
> Hyperterm from accessing the flash.
> Jack Wilson
> wb7eok
Been there..done that..had to return my XL to Kantronics for the same
problem..Kam XL Flash Bios Wizard locks up and unable to communicate with the
TNC.
Now returned with the latest versions loaded. They said the Kam XL Flash Bios
Wizard has not been fully tested by them and recommends using Hperterminal for
downloads.
And as far as I know Kantronics does not read this list..only way to get their
attention is unfortunatly you have to call them on your 'dime' (no 800 number)
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
service@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #84
Date: Mon, 18 Feb 2002 17:38:40 -0600
Message-Id: 64234VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: service@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] TSUELECTRONICA-VENEZUELA
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#623) TSUELECTRONICA-VENEZUELA
<http://www.kantronics.com/forum/index.cgi?review=623>
AUTHOR: HENRY OMAR PARA <KOOSOVO@HOTMAIL.COM>
DATE: Monday, 18 February 2002, at 5:38 p.m.
PLEASE CATALOG. URGENTE. TRANSITORS AND MICROPROCESADORS
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
service@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #85
Date: Tue, 19 Feb 2002 04:08:50 -0600
Message-Id: 1662VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: service@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] Re: KAM XL Flash a Big Problem... HELP!
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#624) Re: KAM XL Flash a Big Problem... HELP!
<http://www.kantronics.com/forum/index.cgi?review=624>
AUTHOR: Norby <lx1no@arrl.net>
DATE: Tuesday, 19 February 2002, at 4:08 a.m.
Reply To: (#621) Re: KAM XL Flash a Big Problem... HELP!
Author: Jack Wilson wb7
Date: Monday, 18 February 2002, at 10:39 a.m.
> After a further review of the list, I did try the upload using the
> Hyperterm program and only after I got of my /XP or /2000 windows boxes
> did it work. I orginally tried the script program that Kantronics provides
> and that is where I was having problems. (Hopefully, Kantronics will read
> these messages.) I tried the script with every version of Windows except
> /95. (I develop software for a living and have multiple computers with the
> various Windows versions for testing). The result was the same every time.
> The Hypertem solution only appears to work on Windows /98. There is
> something about the MS-DOS prompt in Win 2K and /XP the precludes
> Hyperterm from accessing the flash.
Had no problem at all using Hyperterm with NT4SP6a and NT5SP2. Don't have
NT5.1 or DOS-Windows to try.
73 Norby
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
service@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #86
Date: Tue, 19 Feb 2002 09:47:09 -0600
Message-Id: 7187VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: service@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] Winlink Connect
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#625) Winlink Connect
<http://www.kantronics.com/forum/index.cgi?review=625>
AUTHOR: Clay <aa3jy@arrl.net>
DATE: Tuesday, 19 February 2002, at 9:47 a.m.
Just to let the reflector know..that the latest Winlink fix works..made
contact with Winlink Station K4CXJ on his 20 mtr freq.
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
service@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #87
Date: Tue, 19 Feb 2002 14:22:59 -0600
Message-Id: 60197VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: service@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] Re: KAM XL Flash a Big Problem... HELP!
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#626) Re: KAM XL Flash a Big Problem... HELP!
<http://www.kantronics.com/forum/index.cgi?review=626>
AUTHOR: Rick Ruhl <Sales@cssincorp.com>
DATE: Tuesday, 19 February 2002, at 2:22 p.m.
Reply To: (#618) KAM XL Flash a Big Problem... HELP!
Author: Jack Wilson wb7
Date: Sunday, 17 February 2002, at 3:32 p.m.
An update to the XL Wizard has been posted to the CSS site at
http://www.cssincorp.com/pacterm. Go to the download page and you can download
version 1.01.
Kantronics should be putting a link to it on their site soon. This works
around the 65K problem (dealt with the slower speed of the TNC in flash mode).
Rick - W4PC
> Last evening I got my new KAM XL up and running. Checking the website I
> noticed that there was an update available for the flash. I downloaded it,
> followed the instructions and what happened? BIG MISTAKE! It does not
> work! I cannot even get the old .hex file that is on the CD to reinstall.
> Both of them tell me at 65536 that there is an error loading the file. Now
> my unit is down.
> Has anyone been able to get the flash to load? If you did, how did you get
> it to load without erroring out? Any assistance would be greatly
> appreceiated. I don't want to begin feeling like I spent $400.00 for
> nothing!
> Jack Wilson
> WB7EOK
> Everett, WA
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
service@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Message #88
Date: Wed, 20 Feb 2002 01:05:50 -0600
Message-Id: 62165VE7TSI
To: dj1aa@ve7tsi.ampr.org
From: service@kantronics.com
Reply-To: PleaseRespond@TheBulletinBoard
Subject: ['Virtual Elmer' Support Forum] Kantronics Weathernode
The following new message has been posted on 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>.
***************************************************************************
MESSAGE: (#627) Kantronics Weathernode
<http://www.kantronics.com/forum/index.cgi?review=627>
AUTHOR: Trevor Conroy <w7tdc@msn.com>
DATE: Wednesday, 20 February 2002, at 1:05 a.m.
Is there anyone that ones a Kantronics Weathernode? If so please e-mail me. I
have a few questions.
Thanks
W7TDC
Trevor Conroy
w7tdc@msn.com
***************************************************************************
This is an automatically-generated notice. If you'd like to be removed from
the mailing list, please visit 'Virtual Elmer' Support Forum at
<http://www.kantronics.com/forum/index.cgi>, or send your request to
service@kantronics.com. If you wish to respond to this message, please post
your response directly to the board. Thank you!
Area: 'dj1aa' Current msg# 88 of 88.
?,A,APRS,B,BBS,C,D,DX,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,W,X,Y>
*** reconnected to GATE:ON0KUL
Area: 'dj1aa' Current msg# 0 of 0.
?,A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,W,X,Y,Z >
*** reconnected to DB0EIN
=>
------------cut---------------cut---------------cut-------------cut-----------
Have a nice day, greetings Mirko +++ DJ 1 AA / AB 0 DL +++
Read previous mail | Read next mail
| |
