| |
N9LYA > MODS 11.12.00 02:21l 104 Lines 3329 Bytes #999 (0) @ WW
BID : 2717_N9LYA
Read: GUEST
Subj: Aor AR8000 Mod
Path: DB0ABH<DB0ZKA<DB0KFB<F8KOX<F6KNP<F6KVE<F6KIF<F6PTT<F6KDS<F5KCK<GB7SXE<
GB7CIP<GB7WAR<GB7COV<GB7COV<GB7MAX<GB7SAM<GB7OAR<GB7BOB<GB7FYL<GB7FUR<
GB7CRV<EA7URC<IK1ZNW<7M3TJZ<KF9UG<K9XT<K9IU<W9QYQ1<W9QYQ
Sent: 001127/1845 62799@W9QYQ.#SIN.IN.USA.NA
From: N9LYA @ W9QYQ
To: MODS @ WW
N9LYA\paKet 6.2 Msg #: 2717 Date: NOV-27 Time: 17:29
Repost from QRZ CDROM #16
Subject: AR 8000 Filter Mod
Hello AR8000 owners,
To my knowledge no one has actually posted a filter mod, here is what
I did. This is my approach and I only know it works well on my AR8000.
Your results may vary. Others may have a different solution that
works better or worse.
THE GOOD NEWS:
Is it worth the effort. In my opinion YES!
The search mode is vastly improved on the SW bands. Search stops
on the primary frequency and not 1 or 2 times before and after.
Readability of SW stations is vastly improved. In some receiving
instances it reduces adjacent channel interference noticeably.
On AM receive for aviation frequencies a pronounced improvement in
audio quality is noted. You will be able to select WIDE or NARROW
for AM, NFM, USB, LSB.
THE BAD NEWS:
This is a difficult mod to perform. I have been a ham for over 30
years and have extensive homebrew experience. It took all my skill
and a magnifying glass to perform this mod without damaging the
radio. IF YOU ARE NOT QUALIFIED DO NOT ATTEMPT THIS MOD!
Find a qualified helper.
There is no way to adequately describe the locations on the circuit
board to be cut and soldered too. You will have to buy or borrow
a service manual.
Study the electrical mods described below and then using an ohm meter
and the service manual find the locations to modify on the circuit
board.
WHAT IS MODIFIED ELECTRICALLY:
The 4khz filter (F4) circuit is paralleled by a a jumper that is used
to bypass the filter for WIDE reception. This selection process is
accomplished by switching diodes on each end of the filter and bypass.
Find U2 pin 11 (AM, FM filter bypass) line. Trace this line to a 22K
resistor that connects to the switching diodes (near the F4 filter).
The voltage from pin 11 is used to bias these diodes into conduction.
Cut through the circuit trace at a convenient location just before
the 22K resistor.
Find U2 pin 4 (SSB, CW filter inline) line. Trace this line to TWO 22K
resistors that connect to the switching diodes (near the F4 filter).
The voltage from pin 4 is used to bias these diodes into conduction.
Cut through the circuit trace at a convenient location just before
the TWO 22K resistor junction.
Unfortunately there is no way for me to put a schematic in for this
next part but if you draw it out on paper you should be ok. You are
going to mount a small switch on the radio. This will be a SPST
switch.
Connect a wire from the WIDE side of the switch to the single 22K
point.
Connect a wire from the NARROW side of the switch to the dual 22K
resistors point.
Connect TWO 1N914 style switching diodes together to the switch common.
Connect them with the black band facing the switch.
Connect U2 pin 11 to the open end of one diode and U2 pin 4 to the
open end of the other.
What you have done is to install a switch to reverse the normal
filter selection of F4. The 1N914 diodes serve to prevent turning
on the BFO in the AM mode and to prevent grounding when in the
WIDE SSB mode.
I make no guarantees, your results could vary.
You might not have much fun performing this mod but you
will enjoy the results.
73's
Bob
K8WX(WM8P)/GROL/GMDSS/M
73 Jerry
n9lya@w9qyq.#sin.in.usa.na
Read previous mail | Read next mail
| |
