OpenBCM V1.13 (Linux)

Packet Radio Mailbox

DB0FHN

[JN59NK Nuernberg]

 Login: GUEST





  
CX2SA  > SATDIG   30.06.05 09:50l 78 Lines 4927 Bytes #999 (0) @ WW
BID : 4320_CX2SA
Read: GUEST
Subj: AMSAT-BB-digest V2004 #771 3/5
Path: DB0FHN<DB0FOR<DB0SIF<DB0EA<DB0ACC<DB0PKE<DB0RES<ON0AR<7M3TJZ<HG8LXL<
      CX2SA
Sent: 050630/0809Z @:CX2SA.LAV.URY.SA #:4320 [Minas] FBB7.00e $:4320_CX2SA
From: CX2SA@CX2SA.LAV.URY.SA
To  : SATDIG@WW


This is where the planning really paid off:  I gathered up all the bits
and pieces of the antennas and support structures, and started laying
them out on my lawn.  I quickly realized that I had underestimated
(forgotten) the length of the 2M-12 and 432-9WL antennas that I was
going to use.  I thought that they were "only" 18 feet long, so that a 9
foot separation between the elevation rotor and the top of the mast
would be enough to keep them from hitting the 6M-5X antenna at the top.
WRONG!  They are more like 20 and 21 feet long, and I didn't have enough
mast to make that work.  If Mike Stahl from M-Squared is reading this, I
can only apologize in advance to him for how I dealt with this.  Mike, I
took your beautifully engineered, highly optimized antennas and removed
the front couple of boom sections from them to shorten them up so they
would fit!  I know, it's a crime, but if it's any consolation, all I can
say is that you guys designed such superb antennas (in their full
length) that they still gave more than adequate performance after my
temporary butchering of them.  :)  Besides, I promise to put them back
together properly before I install them on my home tower.

More planning:  satellite passes.  In the past, I had used either
Predict or STS-Plus for real-time tracking on my old Pentium laptop
running Windows 95.  That laptop is history, my current laptop is a
Pentium III running Windows 2000, and I could not get either program to
run on it!  Ouch.  Though I haven't given up on them yet, I didn't have
time to figure out the solution to the problems by Field Day.
Fortunately, my Palm Tungsten C came to the rescue, courtesy of Jim
Berry's PocketSat+ program.  This software ran annoyingly slowly on my
old Palm IIIc, but on the Tungsten C, it cranks through the calculations
in the blink of an eye and is a pleasure to use.  I pointed it in the
general direction of the 802.11b wireless access point in my home
network, used the built-in web browser to download keps from amsat.org
(thanks again to Emily, Paul, or whomever arranged for the keps to be
available in PDB format, ready-to-go), and I was in business.  I ran
pass predictions for the three linear birds of interest to me, starting
a few days before Field Day (in case I had time for some practice runs)
and running to the end of the Field Day period.  I set alarms so that
the Palm device, even if turned "off", would "wake up" and warn me every
time a pass was about to begin.  What a blessing to have!  I could now
bang away on the VHF/UHF station in terrestrial mode all I wanted, and
when a good pass was about to start, I could decide if it would be
better to keep going (such as when the 6M sporadic E event was underway)
or to switch over to satellite mode for awhile (when the VHF and UHF
bands were "dead").  And I could still get real-time tracking with
continuously-updated azimuth and elevation information during each pass.

More planning in keeping with KISS:  Not only did I limit myself to one
radio (the FT-847) and no transverters, I also decided to leave the
amplifiers at home.  I certainly didn't need 150 watts on 2M or 100
watts on 70cm for satellite work, and if the terrestrial stations
couldn't hear me at the "barefoot" 50 watts of the FT-847 on those two
bands, would they really hear me much better with less than 1 S-unit of
additional power?  Not only could I bring less gear, I also
automatically avoided the problem of an operator unfamiliar with my
equipment accidentally over-driving the amps and blowing them up.  I
bought the amps used, from an estate sale of a Silent Key, and while
they give me very good service, they aren't the best match to my radio.
The 2M amp wants only 10 watts of drive for full output, and the 70cm
amp wants only 30 watts of drive for full output. I think you can guess
what happens if the power level was turned up to 100% for operation on
6M at 100 watts, and you forget to turn the power back down when you
switch to 2M.  Well, it can't happen if they are home on the shelf!

More planning:  I made sure I had two working sets of headphones (and
one of them needed a little bit of repair work, which was quickly done
after testing revealed a problem), and all the needed audio cables and
adapters to route the signal from the radio to both of them, or to an
external powered speaker.  I also discovered that my planning/testing
was still not as good as it should have been -- although everything
seemed to work audio-wise in testing at home, at the Field Day site I
discovered that the speakers were not shielded well enough, and they
howled from RF entering them when we operated on 6M with the antenna
turned to anywhere within 45 degrees of the direction between the tower
and the operation trailer.  Oh well, we could do without the speakers
and use the headphones 100% of the time, and so that's what we did.


Read previous mail | Read next mail


 16.11.2026 18:02:14lGo back Go up