| |
CX2SA > SATDIG 22.06.05 05:09l 202 Lines 7036 Bytes #999 (0) @ WW
BID : 64699-CX2SA
Read: GUEST
Subj: AMSAT-BB-digest V2004 #752 2/7
Path: DB0FHN<DB0CL<DB0PDF<DB0SM<PI8DAZ<DB0EEO<DB0RES<DK0WUE<7M3TJZ<PY1AYH<
CX2SA
Sent: 050622/0354Z @:CX2SA.LAV.URY.SA #:64699 [Minas] FBB7.00e $:64699-CX2SA
From: CX2SA@CX2SA.LAV.URY.SA
To : SATDIG@WW
Message: 5
Date: Tue, 21 Jun 2005 08:26:46 -0400 (GMT-04:00)
From: Andrew Glasbrenner <glasbrenner@mindspring.com>
Subject: Re: [amsat-bb] Mode S AO51
Hi Art,
In my experience, there are periodic very short fades on 51 that are going to
be tough to overcome. Not a deal breaker on voice, as long as you wait them out
for a few seconds. I experience them portable with the dipole/corner reflector,
or on the 3ft dish, helix/preamp feed.
Another thing I have discovered is that even the circular patches and helixes
exhibit some degree of linearity to them. That sort of thing is tough to tell
mounted on a dish, but holding it by hand it's easy to twist it and hear the
signal level change.
Good Luck.
73, Drew KO4MA
- -----Original Message-----
From: KC6UQH <kc6uqh@cox.net>
Sent: Jun 21, 2005 1:54 AM
To: amsat-bb@amsat.org
Subject: [amsat-bb] Mode S AO51
I have a down converter and I have tried it with both a 3 Turn Helix and a
patch feed. Both are circular polorization LH.
On F.M. I can get 10 dB of quieting at -120 dB on input to my down converter
I have a S5 noise floor and a S9 on AO-51 on peaks, but loose it for a few
seconds every 9 or 10 seconds.
I can point the feed at a florecent light and get a 2 S unit increase in
noise. I think the converter is O.K.
The antenna for the bird is linear. Am I to assume that the null is do to
the change in antenna from the bird rotation ?
I now have the feed on a 20 " dish to try to raise the nuls to an exceptable
level without making the pointing critical.
Anyone else had this experience?
Thanks,
Art, KC6UQH
- ----
Sent via amsat-bb@amsat.org. Opinions expressed are those of the author.
Not an AMSAT member? Join now to support the amateur satellite program!
To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
- ----
Sent via amsat-bb@amsat.org. Opinions expressed are those of the author.
Not an AMSAT member? Join now to support the amateur satellite program!
To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
------------------------------
Message: 6
Date: Tue, 21 Jun 2005 08:24:27 -0400
From: sco@sco-inc.com
Subject: Re: [amsat-bb] SASI Prob
The RAW data stays at 255 and never moves, no matter what levers I push.
Does this mean both rotors are flipped and are at the maximum position now?
I have had strange problems running my SASI with the current version of
NOVA before. Could this be a Nova problem or my rotors are just not
properly aligned?
At 06:40 PM 6/20/2005, you wrote:
>Hi Les,
>
>- let me polish my english lenguage expertise and try to give you a hand
>on this.
>
>Acording to you two mails,it seem to me that you did not calibrated your rotor
>in the Nova for Windows evinronment.
>
>Please start Nova for Windows and click setup--> antenna rotator, next click
>the Interface tab and mark the azimuth rotator range 180-0-180,next mark the
>elevation rotator range 0-180 degrees.This is to define the operating range of
>the two rotators.Please mark the max positions also.
>
>Next click the calibration tag.
>
>Please be shure that your elevation metere reads 0 Zero with the contoller
>switched
>off , if not use the front screw to zero the meter.Switch the controll box
>on and
>turn the elevation rotor to the full horizontal position, antenna level at
>this point,if
>not, adjust it to level position by loosing th respective mechanical
>fixure and thigten
>again. At this point the raw A/D reading in the elevatin window should
>read Zero,
>if not put the number in the minimum A/D reading window, this value is
>equal Zero
>elevation.
>Turm the antenna full clockwise until the reading is 180.At this point the
>reading in
>the Raw A/D reading box shell be 255 and the antenna is horizontal in the
>opposit
>side.
>
>If the reading is not 255, please adjust the Voltage potenciometer at the
>back of
>of the box until you read 255 in the Raw A/D reading box, please correct
>the values
>in the equivalent full clockwise box, ex 255 eqivalent to 180 degrees.
>
>If your meter needel do not shows a fullscale reading, adjust the full
>scale reading pot.
>on the back of the controller box.
>
>Click OK leave the set up tool and click File and Save ALL.
>
>This procedure should be ok for your elevation controller a the tracking
>shall be ok by now.
>Repeat this procedure for the Azimuth controler and your setup is ok for
>full flip over work.
>
>>But Nova says the EL is 180 but the controller says it is 0. Nova says
>>the AZ is 270 but the controller says it is 90.
>
>It loock's like your rotor's are both flipped over into the opposite
>direction.
>The point is that you have to start with NORTH (360 degrees) and horizontal
>position ZERO degrees, otherwise you run nuts.
>
>If all this do not solve the problem , I am sorry there is some other
>problem i do not
>understand.
>
>I hope this helped you to some extend.
>
>73
>Nicolaus Sallay-PP8DA
>n.sallay@vivax.com.br
>Verificado com AVG AntiVirus V 7.0.3
>
>
>------------------------------------------------------------------------------
------------------
>My G5500 rotor is working and the antennas visually move according to the
>dials on the controller.
>
>My G5500 rotor is working and the antennas visually move according to the
>dials on the controller.
>
>But Nova says the EL is 180 but the controller says it is 0. Nova says the
>AZ is 270 but the controller says it is 90.
>
>I am using the SASI Sat Tracker.
>
>Les
>
>I am using the SASI Sat Tracker.
>
>Les
>
>----- Original Message ----- From: <sco@sco-inc.com>
>To: "Nicolaus Sallay" <n.sallay@vivax.com.br>
>Sent: Monday, June 20, 2005 1:24 PM
>Subject: Re: [amsat-bb] SASI Prob
>
>
>>
>>Checked the wires. The controller in my G5500 works OK after I powered
>>off the computer and turned it back on.
>>
>>At 07:24 AM 6/20/2005, you wrote:
>>>Hi Les,
>>>
>>>-try the following, remove the to cover half's of the SASI tracker und
>>>check for broken wire joits at the circuitboard, they are marked Az and
>>>El, I had a similar problem before and found a bad solder point.
>>>
>>>regards
>>>Nicolaus Sallay-PP8DA
>>>n.sallay@vivax.com.br
>>>Verificado com AVG AntiVirus V 7.0.3
>>>
>>>----- Original Message ----- From: <sco@sco-inc.com>
>>>To: <amsat-bb@amsat.org>
>>>Sent: Sunday, June 19, 2005 10:20 PM
>>>Subject: [amsat-bb] SASI Prob
>>>
>>>
>>>>When I plug my SASI Tracker into my G-5500 controller I can move the AZ
>>>>to the right. BUT as soon as I release the lever the needle goes back
>>>>to 0. This does not happen if I unplug the SASI cable.
>>>>Les
>>>>W4SCO
>>>>----
>>>>Sent via amsat-bb@amsat.org. Opinions expressed are those of the author.
>>>>Not an AMSAT member? Join now to support the amateur satellite program!
>>>>To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
- ----
Sent via amsat-bb@amsat.org. Opinions expressed are those of the author.
Not an AMSAT member? Join now to support the amateur satellite program!
To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
Read previous mail | Read next mail
| |