| |
ZL1ABS > PACKET 18.05.07 01:31l 170 Lines 4954 Bytes #999 (0) @ WW
BID : 7C0057ZL1ABS
Read: GUEST
Subj: Xrouter cfg for axudp to AGWpe
Path: DB0FHN<DB0RGB<DB0AAB<DB0PV<DB0MRW<OK0PKL<DB0GRL<SR6BBA<SR1BSZ<F4BWT<
F6KBI<F5GOV<DB0RES<ON0AR<ZL2BAU<ZL1AB
Sent: 070517/2316Z @:ZL1AB.#06.NZL.OC #:60497 [AUCKLAND] FBB7.00i $:7C0057ZL1AB
From: ZL1ABS@ZL1AB.#06.NZL.OC
To : PACKET@WW
AXIP AGWpe 2002.10 Ethernet LAN to AXUDP port on Xrouter
This is what is needed to make Xrouter (LAN IP address 192.168.0.2) send
the unproto traffic (FBB updates, FBB Mail messages, APRS unproto packets,
etc) up the AXUDP port to the AGWpe Packet Switch working on the LAN PC
(IP address 192.168.0.1).
The PIPE & PIPEFLAG lines in the PORT sections are essential. The DIGIPORT
& DIGIFLAG settings are not relevant to the Xrouter to AGWpe Packet Switch
link.
It is assumed that the Radio interfaces and the normal Ethernet interface
are properly installed and working in the connected mode.
I test with a Telnet program in Windows 98se.
- - - - - -
From the Xrouter.cfg file
;
; Example AXUDP pseudo-interface. Apart from "TYPE=AXUDP" see the
; comments relating to AXIP interface.
;
INTERFACE=9
TYPE=AXUDP
MTU=512
ENDINTERFACE
;
; =====================================================================
; Port definitions. Each one begins with PORT=n and ends with ENDPORT
; =====================================================================
;
; The number following PORT= is the port number as displayed by
; the P[orts] command. They do not need to be sequential, you
; may use any number, but you must define them in the order in
; which they are to appear in the list.
;
;
PORT=2
ID= 144.575 MHz 1200 baud APRS Port
INTERFACENUM=2
PORTALIAS2=WIDE1-1 ; for NEW PARADIGM APRS
RFBAUDS=1200
FRACK=7000
RESPTIME=2200
TXDELAY=250
TXTAIL=30
PERSIST=64
RETRIES=10
FULLDUP=0
MHEARD=40
DIGIPORT=3 ;Digipeat to Port3
DIGIFLAG=31 ;Widen-n ON
IDPATH=APRS,WIDE7-7
APRSPATH=WIDE7-7
PIPE=8 ;send to the AXUDP port
PIPEFLAG=63 ;send lots of traffic of all sorts
MAXFRAME=3
PACLEN=120
QUALITY=100
MINTXQUAL=0
MAXTT=5000
ENDPORT
;
;
; Example Ethernet port, supporting IP, ARP and AX25.
; Note the reduced timings (only used for ax25 connections), as
; the defaults are a bit too relaxed for ethernet.
;
;
PORT=3
ID= 144.600MHz F6FBB BBS access Port
PORTALIAS=MAIL-1 ;To digipeat MAIL-1 broadcasts to other port
PORTALIAS2=WIDE1-1 ; for NEW APRS Paradigm
INTERFACENUM=3
RFBAUDS=1200
FRACK=7000
RESPTIME=2200
TXDELAY=250
TXTAIL=30
PERSIST=64
RETRIES=10
FULLDUP=0
CFLAGS=15 ; ok up/downlinks on this port No L3RTT
DIGIFLAG=31 ; Widen-n ON
DIGIPORT=2
PIPE=8 ;Send to the AXUDP port for AGWpe to see
PIPEFLAG=63 ;send lots of traffic to AGWpe
IDPATH=APRS,WIDE7-7
APRSPATH=WIDE7-7
MHEARD=40
IDTEXT=!3645.40S/17442.12E#Albany APRS digi
NODESINTERVAL=90
MAXFRAME=3
PACLEN=120
QUALITY=100
MINTXQUAL=0
MAXTT=5000
ENDPORT
;
PORT=4
ID=Ethernet LAN
INTERFACENUM=4
IPADDRESS=192.168.0.2 ;IP Address of Xrouter
DIGIFLAG=215
APRSPATH=WIDE3-3
CFLAGS=15
RFBAUDS=10000000
FRACK=5000
RESPTIME=300
MAXFRAME=3
PACLEN=240
ENDPORT
;
;
; ---------------------------------------------------
; Example AXIP (AX25 over IP wormhole) port.
; You need one of these for each axip link
; At least ID, INTERFACENUM, and IPLINK must be specified.
; The IPLINK address is the remote host's IP address or hostname.
; Parameters such as TXDELAY, TXTAIL, SLOTTIME, PERSIST, FULLDUP,
; SOFTDCD etc. are meaningless for AXIP, but FRACK, RESPTIME,
PACLEN,
; MAXFRAME, QUALITY etc. operate as normal.
;
;
;PORT=7
; ID=AXIP link with LoungePC
; INTERFACENUM=8
; IPLINK=192.168.0.1
; NODESINTERVAL=15
;ENDPORT
;
;
; ---------------------------------------------------
; Example AXUDP (AX25 over UDP wormhole) port.
; You need one of these for each axudp link
; The IPLINK address is the remote host's IP address or hostname.
; UDPLOCAL and UDPREMOTE are the UDP port numbers for each end of
; the link, and if omitted they default to 93
; Parameters such as TXDELAY, TXTAIL, SLOTTIME, PERSIST, FULLDUP,
; SOFTDCD etc. are meaningless for AXUDP, but FRACK, RESPTIME,
PACLEN,
; MAXFRAME, QUALITY etc. operate as normal.
;
PORT=8
ID=AXUDP link with ZL1ABS-10
INTERFACENUM=9
IPADDRESS=192.168.0.2 ;Local IP Address of Xrouter
UDPLOCAL=93
IPLINK=192.168.0.1 ;IP address of LAN PC running AGWpe
UDPREMOTE=93
NODESINTERVAL=15
CFLAGS=15
SYSOP=1
RESPTIME=800
FRACK=4000
ENDPORT
;
;
73 de Michael ZL1ABS@ZL1AB.#06.NZL.OC
zl1abs@nzart.org.nz
Read previous mail | Read next mail
| |
